manualshive.com logo in svg

Honeywell ControlEdge 900 platform, Hardware Planning And Installation Manual, Page: 109 / 230

Share
Download
Honeywell ControlEdge 900 platform Hardware Planning And Installation Manual Download Page 109

109

Figure 5-21: Wire-Shield Grounding

To facilitate module replacement, it is advisable in most cases to route
all wiring through either the top or the bottom of the terminal block.
This allows the terminal block to pivot up or down, allowing ready
access to the module, and is the preferred method for a limited
number of wires.

For a larger number of wires, or for wires of a heavier gauge, it is
advisable to route some wires through the top of the terminal block,
and some through the bottom, as indicated in

Wire-Shield Grounding

section. In this case, it is necessary to adjust wire length so as to
ensure adequate flexibility of the twisted wires and to provide
clearance sufficient to remove the I/O module.

UIO module wiring

It is 16 Channel universal I/O module, and each channel can be
configured for AI, AO, DI and DO. The UIO is sourcing type.

Figure 5-22: UIO with power connection

Summary of Contents for ControlEdge 900 platform







































































































































































































































Reviews:

No comments