manualshive.com logo in svg

Honeywell CN80 Series, User Manual

Share
Download
Honeywell CN80 Series User Manual Download Page 77

CN80 Mobile Computer Series User Guide

67

Record a Video

This section explains how to record video with the camera in the computer.

1. Open the 

Snapdragon Camera 

app  

. 

2. Tap mode selection 

 in the bottom right corner of the app.

3. Tap 

 to select video.

4. Tap 

 to begin recording video. To zoom in or out, pinch or spread your fingers 

apart.

5. When you are done recording, tap 

.

Change Video Settings

You can change the video settings for best results when recording video.

1. Open the 

Snapdragon Camera

 app 

. 

2. Tap 

 to select video.

3. At the top of the screen, select any of the following to adjust the settings. 

•

Color Filter

 

Stylize your video by applying a filter. Options include: None, Sepia, Negative, 
Solarize, Posterize, and Aqua.

•

Sound/Microphone

Tap to quickly toggle sound recording On or Off. 

•

Advanced Settings

Manually set advanced features. Options include: Flash, Video quality, Video 
duration, GPS location, Storage, and White balance.

Color Filters

Sound/
Microphone

Advanced 
Settings

Summary of Contents for CN80 Series





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands