background image

X-XX UL

INSTALLATION INSTRUCTIONS

69-0309-9

T8602A,B,C,D and TS8602A,C

Chronotherm

®

 III Fuel Saver Thermostats

APPLICATION

These thermostats provide energy saving control for
24 Vac conventional heating/cooling system or 750 mV
heating and 24 Vac cooling as indicated in Table 1.

Power is supplied for the device by three AA alkaline
batteries (included). This allows the thermostat to be com-
patible with all control applications.

Cycle rates are adjustable for heating.

The TS8602 current rating in heating is 0.1A at 750 mV.
The current rating on all other models is 1.6A maximum,
up to 30 Vac.

Adaptive Intelligent Recovery™/Conventional Recovery
selection screw is included on the back of the thermostat.

Fan operation switch is included on the back of some
T8602C models to select either independent or direct
thermostat control of the fan in heating.

12/24 hour clock conversion and 

°

C/

°

F conversion are

available on some models only.

RECYCLING NOTICE

If this control is replacing a control that contains
mercury in a sealed tube, do 

not place your old

control in the trash. Contact your local waste
management authority for instructions regarding
recycling and the proper disposal of your old
control.

If you have any questions, call Honeywell Inc.
at 1-800-468-1502.

INSTALLATION

When Installing This Product…

1

Read these instructions carefully. Failure to follow
them could damage the product or cause a hazard-
ous condition.

2

Check the ratings given on the product to make sure
the product is suitable for your application.

3

Installer must be a trained, experienced service
technician.

4

After installation is complete, check out product
operation as provided in these instructions.

5

Allow thermostat to warm to room temperature
before operating.

Table 1. Thermostat Models.

Stages

Switching

Thermostat

Heat

Cool

System

Fan

Application

T8602A

1

Gas, oil or electric with independently
controlled fan.

T8602B

1

ON-AUTO

T8602B

1

HEAT-OFF

T8602C

1

1

HEAT-OFF-COOL

ON-AUTO

T8602D

1

1

HEAT-OFF-COOL-AUTO

ON-AUTO

T8602C

1

1

HEAT-OFF-COOL

ON-AUTO

Fan operation in heating selectable for

thermostat or independent control; with O
and B terminals for changeover control.

TS8602A

1

Millivolt heating system.

TS8602C

a

1

1

HEAT-OFF-COOL

ON-AUTO

Millivolt heating and 24 Vac cooling

system.

a

Available only in Canada.

®U.S. Registered Trademark
Copyright © 1995 Honeywell Inc.  •            •   All Rights Reserved

Summary of Contents for Chronotherm III T8602A













Reviews: