Honeywell CGW-MB Installation And User Manual Download Page 55

Page: 55 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

CGW-MB Control Features

Modbus Communications

7.19.2 Enabling the Control

CGW-MB control is enabled through a web page-based configuration tool running on the
CLSS Gateway mainboard. Enable control as follows:

1. Start the web browser on a computer that is in the same IP network as the CGW-

MB.

Note

: Chrome is the recommended browser.

2. Enter the following URL in the browser:

https://192.168.10.190:9443/config/index.html

3. Do the following if any security warning is shown. Otherwise, go to step 4.

• Click the

Advanced

link below the error message.

• Agree to proceed.

4. In the

CLSS Gateway mainboard Configuration Tool

page, enter the password.

5. Go to

Modbus Tools

Modbus Settings

6. Enable or disable as needed in the control functionality.
7. Read the

UL Void

message shown, if it is enabled.

8. Click

Save

9. Wait until the CGW-MB shows the changes.
10.Check that the changes are correct.

7.19.3 Control Commands

Using the CGW-MB you can send relevant command values to the holding registers of
Points, Panels, and Zones.

Point Commands

Panel Commands

CAUTION: UL LISTING

ENABLING CONTROL VOIDS THE UL LISTING OF THE CGW-MB.

NOTE:

Refer to the

section for detailed register mapping information.

Serial

No.

Command

Value

Holding Register

EnableDisableDevice

0x400 - Enable

Use Device/Module Holding Register
Address

EnableDisableDevice

0x500 - Disable

Use Device/Module Holding Register
Address

Serial

No.

Command

Lower Byte value

Holding

Register

System Reset

0x0000

20001

Signal Silence

0x0001

20001

Deactivate Buzzer

0xE

20001

Walk Test Sounder on

0xF

20001

Walk Test no sounder on

0x10

20001

Walk test off

0x11

20001

Summary of Contents for CGW-MB




























































































































































































Search results

Summary of Contents for CGW-MB

Reviews:

Honeywell CGW-MB, Installation And User Manual, Page: 55 / 187

Search results

Summary of Contents for CGW-MB

Reviews: