Honeywell CGW-MB Installation And User Manual Download Page 49

Page: 49 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

Modbus Feature Activation

Modbus Communications

7. Scroll down to find

Modbus Support

in the

Features

tab.

8. Enter the number of support required in the

Modbus Support

field.

9. Click

PURCHASE

10.Read the

Confirmation

message and if acceptable, click

CONFIRM

Or
Click

CANCEL

and repeat the steps from 8 to 10.

11.Wait for the purchase to complete and refresh the page, if required.
12.Verify that the purchased number under

Available Features

is correct.

7.12.2 To Activate the Modbus Support

1. Tap

Perform Feature Activation

on the CLSS App’s welcome message.

Figure 7.6: Feature Activation: The First Step

2. Tap

Fixed CLSS Gateway mainboards

3. Select the site of the CLSS Gateway mainboard.
4. Find and tap the OC of the CLSS Gateway mainboard.
5. Tap

ADD ACTIVATION

6. Tap

Modbus Support

under the

One Time Activations

7. Tap

ACTIVATE

8. Wait for the activation successful message.

NOTE:

- The CLSS Gateway mainboard must be already installed. If not, install the fixed CLSS
Gateway mainboard.
- All the network settings should be configured while installing.

Summary of Contents for CGW-MB




























































































































































































Search results

Summary of Contents for CGW-MB

Reviews:

Honeywell CGW-MB, Installation And User Manual, Page: 49 / 187

Search results

Summary of Contents for CGW-MB

Reviews: