manualshive.com logo in svg

Honeywell CGW-MB, Installation And User Manual, Page: 37 / 187

Share
Download
Honeywell CGW-MB Installation And User Manual Download Page 37

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

36

Troubleshooting

Post-Installation Activities

Table 6.1. LED-Indicated Issues and Possible Fixes (Continued)

6.2.2  To Troubleshoot Other Issues

If there are issues, which are not shown by the LEDs, refer to the below table to determine 
their possible fixes. 

DL4: 

CLSS Site Manager

 LED-Indicated Issues

CLSS Site Manager

 LED 

Status

Other LEDs’ Status

Possible Fixes

 Flashing Green every 

0.25 second

 •

DL3

 The panel LED is flashing 

once per second

 •

DL2

 The Trouble LED is OFF

 • Associate the CLSS Gateway 

mainboard board with the user 
account. 

 • Ensure that the user account is 

active.

 • Ensure that the panel’s date and 

time are correct.

DL5: Wireless LED-Indicated Issues

Wireless LED Status

Other LEDs’ Status

Possible Fixes

 OFF

 •

DL3

 The panel LED is flashing 

once per second

 •

DL4

 The 

CLSS Site Manager

 

LED is OFF

 • Ensure that the WLAN settings in 

the CLSS Gateway mainboard 
configuration tool

 

are correct.

 • Ensure that the building’s IP 

network has Internet and 

CLSS 

Site Manager

 connectivity. 

DL6: Mobile LED-Indicated Issues

Mobile LED Status

Other LEDs’ Status

Possible Fixes

 OFF

 •

DL3

 The panel LED is 

flashing once per second

 •

DL4

 The 

CLSS Site Manager

 

LED is OFF

1. On the CLSS Gateway mainboard 

board, find the S8 button. To find 
the S8 button, refer to 

Figure 2.1

.

2. Press the S8 button until the LED 

indicator DL6 flashes fast, 
indicating enabled mobile 
connectivity. 

Events-Related Issues

Issue Description

Possible Causes

Possible Fixes

 Panel events are not 

displayed on the 

Connected Life Safety 
Services

 App

 The CLSS Gateway mainboard is 

dissociated.

 Associate the CLSS Gateway 

mainboard board with the user 
account. 

 The user account is not 

associated with the CLSS 
Gateway mainboard.

 Ensure that the user account is 

active.

 The panel’s date and time are 

incorrect.

 Ensure that the panel’s date and time 

are correct.

Summary of Contents for CGW-MB




























































































































































































Reviews:

No comments