Honeywell CGW-MB Installation And User Manual Download Page 185 | Manualshive

Page: 185 / 187

Honeywell CGW-MB Installation And User Manual Download Page 185

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

184

VESDA® Detectors

Connecting to the Panels

C.14 VESDA® Detectors

C.14.1 Connection Options

The CLSS Gateway mainboard operates with VESDA detectors and sends alarm data to
users.

Minimum Required Versions

For VESDA-E: All VESDA-E detector versions
For Android App: 1.0.0.2493 (2493)
For iOS App: 0.3.0 (1124)
For the CGW-MB: 3.0.4.70

C.14.2 To Use an Ethernet Connection

Using an Ethernet cable the CGW-MB and the VESDA detectors are connected.

Before Connecting

1. In the Configuration Computer

1. Install the VSC Tool (with a valid license) on the Configuration Computer.
2. Connect the USB ports of the Configuration Computer and the detector with a

Type B cable.

2. In the detector:

• Using the VSC Tool, configure the respective parameters, including the

authentication password.

• Using the VSC Tool, create a connection profile for Ethernet.
• If detector connector is used, ensure that the detectors are connected with the

detector connector.

3. In the CGW-MB: Ensure that the CLSS Gateway mainboard is connected with

CLSS

Site Manager

via Ethernet or Wireless.

1. On the CLSS Gateway mainboard Side

Connect the Ethernet cable to the Ethernet port 2 of the CLSS Gateway mainboard.
Refer to

where it is labeled as the Ethernet Port 2. It is the J3 pin on the

CLSS Gateway mainboard board.

2. On the Detector Side

Connect the Ethernet cable to the Ethernet port of the detector.

3. Power Connection

The CLSS Gateway mainboard can receive the 24V DC power from an external power

supply.

On the CLSS Gateway mainboard Side

• Connect the Red wire to the +ve pin of the power supply port.
• Connect the Black wire to the -ve pin of the power supply port.

NOTE:

The CGW-MB can connect with a VESDA detector or a VESDA Detector Connector.

NOTE:

The detector’s power supply to the CLSS Gateway mainboard must be 24V

DC power.

!

WARNING: ENSURE THAT THE BATTERY BACKUP CAPACITY OF A CONNECTED SMOKE DETECTOR IS

CORRECTLY CALCULATED. POWER THAT THE CLSS GATEWAY MAINBOARD ALSO WOULD CONSUME

SHOULD BE CONSIDERED IN THE CALCULATION.

«
...
183
184
185
186
187
»

Summary of Contents for CGW-MB




























































































































































































Reviews:

No comments