background image

F76S WATER FILTERS AND MV876B AUTOMATIC-BACKWASH CONTROLS

62-3015—4

12

F76A,G REPLACEMENT PARTS LIST (SEE FIG. 14)

N/A = Part number not available at time of printing.

a

Sold in packs of ten.

b

PF76C1023 does not include drain tap and red handle and screw.

Description

1/2 inch

3/4 inch

1 inch

1-1/4 inch

1-1/2 inch

2 inch

(A)

 

Pressure Gauge

F76A 

F76B

0901537 0901537 0901537 0901537 0901537  0901537 

F76G & F76H

5267400

5267400

5267400

5267400

5267400

5267400

(B)

 

Tailpieces (for new and old style)

Sweat

U76S5007 U76S5015 U76S5023 U76S5031 U76S5039  U76S5047 

Threaded (shown)

U76T1004

U76T1014

U76T1022

U76T1030

U76T1038

U76T1046

(C)

 

Union Nuts

N/A

N/A

N/A

N/A

N/A

N/A

(D)

 

Tailpiece Gaskets

a

0901444

0901444

0901445

0901446

0901447

0901448

(E)

 

Ring (plastic)

N/A

N/A

N/A

N/A

N/A

N/A

Screen Kit

20 Micron

QF76Q2007 QF76Q2007 QF76Q2015 QF76Q2015 QF76Q2023

QF76Q2023

50 Micron

QF76R2030

QF76R2030

QF76R2038

QF76R2038

QF76R2046

QF76R2046

100 Micron

QF76S2051

QF76S2051

QF76S2059

QF76S2059

QF76S2067

QF76S2067

200 Micron

QF76T2074

QF76T2074

QF76T2082

QF76T2082

QF76T2090

QF76T2090

Includes: 
(F) Upper Screen 
(H) Barrel O Ring
(L) Lower Screen

Internal Seal Kit

Includes: (H) Barrel O Ring
(K) Screen Seal
(Q) Chamber O Ring
(S) Joint Ring Seal

N/A

N/A

N/A

N/A

N/A

N/A

Filter Insert Kit

(F) Upper Screen 
(G) Upper Guide Barrel
(H) Barrel O Ring
(J) Lower Guide Barrel
(K) Screen Seal
(L) Lower Screen
(M) Impeller
(N) Lower Screen Support
(P) Conical Base Spring
(Q) Chamber O Ring

QF76G2053 QF76G2053 QF76G2061 QF76G2061 QF76G2069

QF76G2069

Filter Sump Kits

Clear Plastic

PF76C1007

PF76C1007

PF76C1015

PF76C1015

PF76C1023

b

PF76C1023

b

Bronze

202913

202913

202914

202914

202915

202915

 Includes: 
(Q) Chamber O-Ring 
(R) Sump 
(S) Joint Ring Seal 
(T) Drain Tap (Backwash Outlet)

b

(U) Red Handle and Screw

b

(U) Red Handle and Screw

251550

251550

251550

251550

251550

251550

Sump Wrench

ZR10K-12

ZR10K-12

ZR10K-1

ZR10K-1

ZR10K-112

ZR10K-112

Summary of Contents for Braukmann F76S

















Reviews: