manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Honeywell AUTOMATIC CONTROL Engineering Manual is an essential resource for professionals seeking in-depth knowledge on control systems. This comprehensive manual covers various aspects of automatic control, providing valuable insights and practical guidance. Download your free copy exclusively from manualshive.com, the go-to hub for user manuals.

Share
Download
background image

INDOOR AIR QUALITY FUNDAMENTALS

152

ENGINEERING MANUAL OF AUTOMATION CONTROL

Dioctyl  phthalate: An oily  liquid used in testing filters.

Dose: The amount of a given agent that actually reaches the

site in the body where it causes an effect.

Electrostatic air cleaner: A device that has an electrical charge

to trap particles traveling in the airstream.

Emission: The release of airborne contaminants from a source.

Emission rate: A measure of the quantity of a chemical released

into the air from a given quantity of a source during a
given amount of time.

Emission standard: Either a voluntary guideline or a

government regulation that specifies the maximum rate
at which a contaminant can be released from a source;
also called source emission standard.

Environmental Tobacco Smoke (ETS): Combustion

emissions (composed of over 3800 identifiable
contaminants, including 43 known or suspected
carcinogens) released either by burning tobacco or
exhausted tobacco smoke.

Flushout: A preoccupancy preventive procedure which involves

running a ventilation system on its highest settings to
remove the airborne emissions from newly installed
furnishings and carpeting. See Bakeout.

Formaldehyde (HCHO): An odorous Volatile Organic

Compound (VOC) that contains oxygen in addition
to carbon and hydrogen which is usually in the form
of a colorless gas at room temperature.

Fungi:  Unicellular or multicellular eukaryotic organisms

embracing a large group of microflora  including
molds, mildews, yeasts, mushrooms, rusts, and smuts.

HEPA filter: A classification of high-efficiency particulate air

filters.

Hypersensitivity disease: A type of disease characterized by

allergic responses to antigens.

Indoor Air Quality (IAQ): The characteristics of the indoor

climate of a building, including the gaseous
composition, temperature, relative humidity, and
airborne contaminant levels.

Legionnaires disease: One of two important diseases (the other

being Pontiac fever) that are caused by legionella
pneomophila bacteria. The disease is a severe
multisystemic illness that can affect not only the lungs
but also the gastrointestinal tract, central nervous
system, and kidneys.

Materials Safety Data sheets (MSDSs): OSHA required

documents supplied by manufacturers of potentially
hazardous products. MSDSs contain information
regarding potentially significant airborne
contaminants, precautions for inspection, health
effects, odor description, volatility, expected
contaminants from combustion, reactivity, and
procedures for spill cleanup.

Micro-organisms:  Life forms too small to be seen with the

unaided eye.

Mitigation:  A procedure or strategy aimed at reducing or

eliminating an indoor air problem, through source
control, ventilation control, exposure reduction, and
air cleaning.

Multiple Chemical Sensitivities (MCS): A medical condition

affecting several organs in which a person reports
sensitivity to very low doses of a variety of
chemicals after an identifiable chemical exposure
to one chemical.

National Ambient Air Quality Standard (NAAQS): The U.S.

outdoor air quality standards designed to protect public
health. Pollutants covered by the NAAQS include
ozone, sulfur dioxide, nitrogen dioxide, lead,
respirable particulates, and carbon monoxide.

Occupied Zone: The area in a room or building in which most

human activity takes place, considered by ASHRAE
to be between 3 and 72 inches from the floor and 2
feet from walls or fixed equipment.

Off gassing: The release of gases, such as organic vapors, from

a building material after the manufacturing process is
complete.

Particulates:  Small  airborne particles found in the indoor

environment that include fibrous material, solid-state
semivolatile organic compounds such as Polycyclic
Aromatic Hydrocarbons (PAHs), trace metal, and
biological materials.

Permissible Exposure Limit (PEL): Air contaminant

standards set by OSHA.

4-phenylcyclohexene(4-PC): An odoriferous compound that

is a by-product of the manufacture of styrenebutadiene.

Pollutant: A contaminant that is known to cause illness; often

used synonymously with contaminant.

Pollutant pathway: Route of entry of an airborne contaminant

from a source location into the occupant breathing
zone through architectural or mechanical connections
(e.g. through cracks in walls, vents, HVAC system
ducts, and open windows.

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AUTOMATIC CONTROL

Radio Shack 4 Owner'S Manual preview
4
Brand: Radio Shack Pages: 52
Samson 580 Translation Of The Original Operating Instruction preview
580
Brand: Samson Pages: 36
FBII XL-2T Hookup And Installation Instructions preview
XL-2T
Brand: FBII Pages: 71
CAME Z Series Connection Manual preview
Z Series
Brand: CAME Pages: 4
Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Brand: Galcon Pages: 32
National Instruments 9853 Getting Started Manual preview
9853
Brand: National Instruments Pages: 29
National Instruments PXIe-4302 Calibration Procedure preview
PXIe-4302
Brand: National Instruments Pages: 14
National Instruments PXIe-4302 User Manual preview
PXIe-4302
Brand: National Instruments Pages: 31
National Instruments NI-9244 User Manual And Specifications preview
NI-9244
Brand: National Instruments Pages: 50
National Instruments NI 9870 Operating Instructions And Specifications preview
NI 9870
Brand: National Instruments Pages: 24
National Instruments NI 9247 Getting Started Manual preview
NI 9247
Brand: National Instruments Pages: 21
National Instruments NI 9242 Getting Started Manual preview
NI 9242
Brand: National Instruments Pages: 39
National Instruments NI 9218 Getting Started preview
NI 9218
Brand: National Instruments Pages: 22
National Instruments NI 9263 Calibration Procedure preview
NI 9263
Brand: National Instruments Pages: 8
National Instruments NI 9425 Getting Started Manual preview
NI 9425
Brand: National Instruments Pages: 20
National Instruments NI 9234 Getting Started preview
NI 9234
Brand: National Instruments Pages: 9
National Instruments FIeldPoint FP-AO-200 Operating Instructions Manual preview
FIeldPoint FP-AO-200
Brand: National Instruments Pages: 13
National Instruments NI 9205 Getting Started Manual preview
NI 9205
Brand: National Instruments Pages: 26

Brands by name

Popular brands

Load more brands