manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Share
Download
Honeywell AUTOMATIC CONTROL Engineering Manual Download Page 155

MICROPROCESSOR-BASED/DDC FUNDAMENTALS

145

ENGINEERING MANUAL OF AUTOMATIC CONTROL

Design, Write, and Compile Program

The actual process of designing and writing the control loop

programs can be a very complex or a relatively straightforward
procedure, depending on the language processing software
provided for the controller. The microprocessor-based
controller understands instructions only at the most elementary
language level, i.e., strings of 1s and 0s or machine code.
Because of this, language processing software is often required.
This software translates the instructions of a control program
written  in an easier-to-use high-level language into actual
machine code. The terms compiler, assembler, object oriented,
or interpreter are used to describe types of language processing
software packages. The assembler is normally associated with
a lower level assembly language while the compiler, object
oriented, or interpreter is normally associated with a higher
level language. Most system level controllers today are
programmed using an object oriented (graphical) language.

Object-oriented languages often are custom software

packages tailored to the requirements of a specific vendor’s
controller. Control sequences are built by selecting
preprogrammed control blocks, for example the PID algorithm,

and linking them with other control blocks. Although this
process requires little or no knowledge of programming, it does
require in-depth knowledge of the control blocks and the
specific HVAC process.

Debug, Install, Enter Data Files, and Test

Regardless of the custom control program used, each

program must be debugged to assure proper operation. When
programs are written on a host machine, special debug and
simulation programs are frequently employed prior to installing
the program in the controller. Debug programs test for syntax
(language) and procedural errors. Simulation programs allow
inputs and outputs to be simulated and a static test of the
program to be run. After debug and error correction, the
program and associated data files are loaded into the controller
and a full system check is made under normal operating
conditions to assure proper operation.

Some systems allow graphically constructed programs to be
monitored live in their actual executing environment with
inputs, outputs, and intermediate signal values updating
continuously.

TYPICAL APPLICATIONS

ZONE-LEVEL CONTROLLER

Zone-level controllers can be applied to a variety of types

of HVAC unitary equipment. Several control sequences can
be resident in a single zone-level controller to meet various
application requirements. The appropriate control sequence is
selected and set up through either a PC for the system or through
a portable operator’s terminal. The following two examples
discuss typical control sequences for one type of zone-level
controller used specifically for VAV air terminal units. For
further information on control of terminal units, refer to the
Individual Room Control Applications section. As stated in
the introduction, the following applications are for stand-
alone  controllers. See the Building Management System
Fundamentals section for network applications.

EXAMPLE 1. VAV COOLING ONLY

In a pressure independent VAV cooling only air terminal

unit application the zone-level controller controls the primary
airflow independent of varying supply air pressures. The
airflow setpoint of the controller is reset by the thermostat to
vary airflow between field programmable minimum and

maximum settings to satisfy space temperatures. On a call for
less cooling, the damper modulates toward minimum. On a
call for more cooling, the damper modulates toward maximum.
The airflow control maintains the airflow at whatever level
the thermostat demands and holds the volume constant at that
level until a new level is called for. The minimum airflow
setting assures continuous ventilation during light loads. The
maximum setting limits fan loading, excessive use of cool air,
and/or noise during heavy loads.

EXAMPLE 2. VAV COOLING WITH

SEQUENCED ELECTRIC REHEAT

In a VAV cooling air terminal unit application with sequenced

electric reheat, an adjustable deadband is provided between
the cooling and the reheat cycle. During cooling the control
mode is constant discharge temperature, variable volume. On
a call for less cooling, the damper modulates toward minimum
flow. The damper remains at minimum cooling through a
deadband. On a call for reheat, the damper goes from minimum
flow to reheat flow to ensure proper air distribution and prevent
excessively high discharge temperatures and to protect the
reheat elements. In this sequence, duct heaters are cycled and

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands