background image

READ IT

 

OR

 

WATCH IT

Read instructions or watch easy-to-follow video. 

Scan QR code or visit http://bit.ly/2VKpTZM

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS 
standards. Operation is subject to the following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation.

FCC NOTE:

 The manufacturer is not responsible for any radio or TV interference caused by 

unauthorized modifications to this equipment. Such modifications could void the user’s 
authority to operate the equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy, and if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver  

is connected.

— Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3(B)/NMB-3(B)

Questions? Contact our U.S.-based Consumer Care at 1-855-698-8324,                           

Monday–Friday, 7AM–8PM CST.
For the most up-to-date product support, accessories, electronic (PDF) format manuals and 

more, visit www.byjasco.com/support.

DO NOT RETURN THIS 

PRODUCT TO THE STORE

STOP

FCC/IC

SPECIFICATIONS

RISK OF ELECTRICAL SHOCK

• DO NOT USE IN WET LOCATIONS
• USE INDOORS ONLY
• USE ONLY INSULATED STAPLES OR 

PLASTIC TIES TO SECURE THE CORDS

• ROUTE AND SECURE THE CORDS SO 

THAT THEY WILL NOT BE PINCHED OR 

DAMAGED

NO SERVICEABLE PARTS
NON-REPLACEABLE LEDS

LED LIGHT OUTPUT IS STRONG

ENOUGH TO INJURE HUMAN EYES.

PRECAUTIONS MUST BE TAKEN TO

PREVENT LOOKING DIRECTLY AT THE

LEDS WITH UNAIDED EYES FOR MORE
THAN A FEW SECONDS

RISK OF FIRE

• NOT INTENDED FOR ILLUMINATION OF 

AQUARIUMS

• NOT INTENDED FOR USE ABOVE 

STOVES, COOK TOPS, SINKS OR OTHER 

HEAT PRODUCING APPLIANCES, SUCH 

AS COFFEE MAKERS, TOASTERS, OR 

TOASTER OVENS

• NOT INTENDED FOR RECESSED 

INSTALLATION IN CEILINGS OR 

SOFFITS

• NOT INTENDED FOR SURFACE 

INSTALLATION INSIDE OR ON TOP 

OF BUILT-IN FURNISHINGS SUCH AS 

KITCHEN CABINETS, CHINA CABINETS, 

OR TROPHY CASES 

• DO NOT CONCEAL POWER SUPPLY 

CORD OR LINKING CORDS INSIDE 

A WALL, CEILING, SOFFIT, KITCHEN 

CABINET, OR SIMILAR PERMANENT 

STRUCTURE 

• DO NOT RUN THE POWER SUPPLY 

CORD OR LINKING CORDS THROUGH 

HOLES IN WALLS, CEILINGS OR 

FLOORS

WARNING

FIGURE 2

FIGURE 3

INSERT

SLIDE

45415, 45417, 45418

PLUG-IN 

LED PUCK LIGHTS

SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR CABINET 

SO YOU CAN REFER TO THEM AT A LATER TIME.
WARNINGS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK 

OR INJURY TO PERSONS: 
IMPORTANT SAFETY INSTRUCTIONS

This portable light has a polarized plug (one blade is wider than the other) as a feature to reduce 

the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not 

fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never 

use with an extension cord unless plug can be fully inserted. Do not alter the plug. Read entire 

installation procedure before you begin. 

INSTALLATION PROCEDURE FOR PLUG-IN UNIT

Carefully plan out your installation prior to securing your LED Puck Light to the mounting 

surface, making sure that your 5ft. line cord will reach the nearest electrical outlet. For kitchen 

installations, the recommended mounting for the Puck Light is near the front lip of your kitchen 

under cabinets as shown in the illustration 

Figure 1

. This provides the best light distribution 

across a countertop.

1.  DO NOT ATTEMPT TO INSTALL FIXTURE WHILE  

 

  PLUGGED IN.
2.  Select a suitable dry mounting location (for use  

 

  indoors only.) Make sure mounting surface is capable    

  of supporting the fixture.
3.  Locate positions where LED puck should be mounted.   

  (Keep in mind linking cord.)
4.  Use the keyhole taps on the end of the fixture to mark    

  the appropriate screw hole locations. Pre-drill holes  

 

  in the mounting surface with a 1/16” (1.5mm) drill  

 

  bit for soft woods and a 3/32” (2.4mm) drill bit for hard  

  woods. Since mounting is via keyholes, the screw heads  

  should protrude approximately 1/8” (3.2mm) beyond    

 surface.
5.  After installing mounting screws (included), secure  

 

  the LED puck to mounting surface via keyholes by  

 

  tightening the mounting screws. See 

Figure 2

 and  

 

 

Figure 3

.

6.  Plug fixture into a 120VAC 60Hz outlet.

CLEANING INSTRUCTIONS

Your fixture is made from quality materials that will last for many 

years with minimum care. When cleaning, make sure you have 

unplugged your fixture and have allowed sufficient time for the 

unit to cool to room temperature. You should clean the housing 

and lens using a soft, damp cloth. You should plug your fixture 

back in only after the fixture has thoroughly dried. 

FIGURE 1

CABINET

COUNTER TOP

W

ALL

The Honeywell Trademark is used under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
This product is manufactured by Jasco Products Company LLC.
This Jasco product comes with a limited-lifetime warranty. Visit www.byjasco.com for warranty details.

MADE IN CHINA/HECHO EN CHINA
©JASCO 2019 | 45415, 45417, 45418 | 05/06/19 v1

Jasco Products Company LLC,

10 E. Memorial Road

Oklahoma City, OK 73114

120VAC 60Hz
385 Lumens
83 CRI
2700K Warm White

120VAC 60Hz
775 Lumens
83 CRI
2700K Warm White

120VAC 60Hz
1150 Lumens
83 CRI
2700K Warm White

45415

45417

45418

Reviews: