manualshive.com logo in svg

Honeywell 4286, Set Up And Troubleshooting, Page: 1 / 11

Share
Download
Honeywell 4286 Set Up And Troubleshooting Download Page 1

 

Back to Top

 

- 1 -

 

 

 

Step-by-Step 

Tech Support 

 Updated 7/27/10 

4286/4500 Voice Module Set up and Troubleshooting 

 

In this document we will discuss the following: 

1.

 

Pre-Installation Notes

 

2.

 

The Wiring

 

3.

 

System Programming

 

4.

 

4286 1

st

 Time Accessing and Programming

 

5.

 

4500 Integration

 

6.

 

4500 Troubleshooting

 

7.

 

4286 Troubleshooting

 

8.

 

Voice Descriptor Word List

 

 

Pre-Installation Notes: 

1.

 

VOIP phone service is not supported. 

2.

 

DSL requires an RJ31X DSL filter. 

 

Wiring Notes: 

1.

 

When using a power supply you MUST share a common ground with the control panel.

 

2.

 

The 4286 wires up directly to the keypad Terminals on your Control panel.

 

3.

 

Observe the panels ECP (keypad data) wire runs and do not exceed the 2000’ max distance the panel offers 
(1500’ on vista20 and lower control panels).

 

4.

 

Existing wires connected to the “Handset” terminals on control must be moved from there to terminals 3 
and 4 on the 4286.

 

5.

 

Place a 2 conductor wire between terminals 21 and 22 to terminals 1 and 2 on the 4286.

 

 

 

Figure 1: Vista-10/15/20p Wiring

 

Summary of Contents for 4286












Reviews:

No comments