Honeywell 15-0705-5 Component Maintenance Manual With Illustrated Parts List Download Page 30 | Manualshive

Page: 30 / 113

Honeywell 15-0705-5 Component Maintenance Manual With Illustrated Parts List Download Page 30

COMPONENT MAINTENANCE MANUAL

15-0705

• TASKS are numbered from 801 thru 999

• SUBTASKS are numbered from 001 thru 800.

(e)

Element 6 is a three position alphanumeric element used for identification of differences
in configurations, methods or techniques, variations of standard practice applications, etc.

(f)

Element 7 provides coding of those tasks or subtasks that have been changed by the
customer (e.g., those tasks or subtasks accomplished by an outside repair source).

Figure INTRO-3. (Sheet 1 of 1) MTOSS Code Positions

(GRAPHIC 33-30-15-99B-803-A01)

Table INTRO-2. MTOSS Function Code Definitions

Code

Function

Definition

000

REMOVAL AND DISASSEMBLY

010

Removal

Removal of the engine/component from a
workstand, transport dolly, test stand, etc., or
aircraft.

020

Remove Modular Sections

This is the first echelon of disassembly which
consists of sectionalization of the unit/engine
into primary modular sections. Modular
sections are identified by the third element
of the ATA number when removed from the
unit/engine.

030

Disassemble Modular Sections

This is the second echelon of disassembly
which consists of disassembly of the modular
sections into subassemblies after removal from
the unit/engine. Modular section designations
appear in the second element of the ATA
number for this echelon of disassembly.

EFFECTIVITY

ALL

33-30-15

Page INTRO-6

30 Mar 2017

© Honeywell International Inc. Do not copy without express permission of Honeywell.

«
...
28
29
30
31
32
...
»

Summary of Contents for 15-0705-5


















































































































Reviews:

No comments