Honeywell 145*g1D User Manual Download Page 72

Page: 72 / 206

4 - 2

Good Read and Error Indicators

Beeper – Good Read

The beeper may be programmed

Off

in response to a good read. Turning this option off, only turns off the beeper

response to a good read indication. All error and menu beeps are still audible.

Default = Beeper - Good Read On.

Beeper Volume – Good Read

The beeper volume codes modify the volume of the beep the scanner emits on a good read.

Default = High.

Beeper Pitch – Good Read

The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.

Default = Medium.

Trigger Click On

Beeper - Good Read Off

* Beeper - Good Read On

Low

Medium

* High

Off

Low (1600 Hz)

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands