Honeywell 145*g1D User Manual Download Page 126

Page: 126 / 206

7 - 24

EAN/JAN-13 Addenda

This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.

Default = Off for both 2 Digit and 5 Digit

Addenda.

EAN/JAN-13 Addenda Required

When

Required

is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda.

Default = Not Required.

EAN/JAN-13 Addenda Separator

When this feature is

, there is a space between the data from the bar code and the data from the addenda. When turned

Off

, there is no space.

Default = On.

Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to

UPC-A/EAN-13 with Extended Coupon

Code

(page 7-19).

2 Digit Addenda On

* 2 Digit Addenda Off

5 Digit Addenda On

* 5 Digit Addenda Off

Required

* Not Required

* On

Off

Summary of Contents for 145*g1D















































































































































































































Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands

Honeywell 145*g1D, User Manual

Search results

Summary of Contents for 145*g1D

Reviews:

Related manuals for 145*g1D

Brands by name

Popular brands