Honeywell 03251385 Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 20

background image

GB-17

D

GB

F

NL

I

E

Flue gas connector FLUP

The FLUP is not supplied with the ECOMAX

®

and

must be ordered separately.
If the FLUP is ordered with the ECOMAX

®

, it will be

supplied ready-fitted on the burner.

Air connection set

Specially machined barrel nipple which ensures a
reliable, correct measurement at the orifices installed
in the burner. The /E version is installed when the
burner is supplied.

Ceramic radiant tube SER-C

1

2

3

4



Burner gasket



Flange connection



Radiant tube (SiSiC)

4

Mounting gasket

For heat treatment processes in which combustion
gases must be kept separate from the product. The
patented flange connection is air-tight.
Material: SiSiC, max. application temperature:

1300°C.
The SER-C is not supplied with the ECOMAX

®

and

must be ordered separately.

Flue gas guide tube FGT for SER-C

To guide the flue gases if smaller burners are used

than are standard for the radiant tube diameter.
Material: vacuum moulded pulp.

Available on request in different sizes suitable for the

SER-C radiant tube and ECOMAX

®

burner sizes.

Segmented flame tube SICAFLEX

®

Segmented ceramic flame tubes to guide hot flue
gases in radiant tubes.
Material: SiSiC.

The SICAFLEX

®

is not supplied with the ECOMAX

®

and must be ordered separately.

Purge air/cooling air nozzles

Nozzles to limit the volume of purge air in order to
achieve safe ignition and monitoring of the ECOMAX

®

and to avoid condensation and overheating.

Nozzle for electrode purge

Burner

Designation

of nozzle

Order number

ECOMAX

®

0

nozzle electrode

ECO 0

G 1/4 D=2.5 /E

21802944

ECOMAX

®

1 – 3

nozzle electrode

ECO 1-3

G 1/4 D=2.5 /E

21802945

ECOMAX

®

4 – 6

nozzle electrode

ECO 4-6

G 1/4 D=4.0 /E

21802946

UV sensor purge air nozzle

Burner

Designation of nozzle Order number

ECOMAX

®

0 – 3

nozzle UV ECO 0-3
G 1/4 D=2.5 /B

21802989

ECOMAX

®

4 – 6

nozzle UV ECO 4-6
G 1/4 D=4.0 /B

21802990

Purge air connection set

To connect the purge air for the spark electrode or

UV sensor.

Designation

Order number

PURGE AIR-SET 1/4-8/6 ECO PTFE-1M

21803332

PURGE AIR-SET 1/4-8/6 ECO PTFE-2M 21803645

«
...
15
16
17
18
19
...
»

Summary of Contents for 03251385





















Reviews:

No comments

Related manuals for 03251385

Brand: Bentone Pages: 148

Brand: Comtherm Pages: 25

Brand: Kudu Pages: 8

Brand: Riello Pages: 12

Brand: Warmington Pages: 29

Professional Series PRO36RBI

Brand: Capital Pages: 2

Brand: Capital Pages: 2

Professional Series PRO32RBI

Brand: Capital Pages: 2

E10.12000.37 L-EUF

Brand: ECB Pages: 42

Multicalor 300.1

Brand: Ecoflam Pages: 24

Brand: Giersch Pages: 30

564 HO DiamondFyre

Brand: Travis Industries Pages: 6

Brand: Megatherm Pages: 23

Brand: Megatherm Pages: 25

Low-NOx N10.12000.30 G-EU2

Brand: elco Pages: 34

Brand: elco Pages: 44

Brand: elco Pages: 43

Firebird FB 4 R LN

Brand: elco Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands