Honda NC700 2012, Service Manual

Page: 359 / 773

12-4
dummyhead dummyhead
DUAL CLUTCH TRANSMISSION (DCT) (NC700XD/SD)
Linear Solenoid Valve Function Procedures
• If the PCM has a DTC, the function test does not work.
• The function test is not for the quality check of the linear solenoid valve.
• Do not open the throttle while testing the linear solenoid valve function.
Conduct a test of the linear solenoid valves when the linear solenoid valves have been serviced or replaced.
1. Connect the HDS pocket tester.
2. Select the "DRIVE TRAIN MODE MENU".
3. Select the "FUNCTION TEST" and then select the "Linear Solenoid".
4. Select the "Linear Solenoid 1" or "Linear Solenoid 2".
5. Start the engine and let it idle.
6. Make sure that the transmission is in neutral position.
7. Select the "Drive Linear Solenoid To 0 kPa", "Drive Linear Solenoid To 400 kPa" or "Drive Linear Solenoid To 800 kPa" mode.
Measure the linear solenoid current at each mode.
SPECIFICATIONS
Unit: mm (in)
TORQUE VALUES
ITEM STANDARD SERVICE LIMIT
Clutch clearance 0.9 – 1.1 (0.035 – 0.043) 2.0 (0.08)
EOT sensor resistance (20°C/68°F) 2.5 – 2.8 k
Ω
–
ITEM Q'TY
THREAD TORQUE
REMARKS
DIA. (mm) N·m (kgf·m, lbf·ft)
Solenoid valve stopper plate bolt 1 6 12 (1.2, 9) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
Right crankcase cover wire clamp
bolt 2 6 12 (1.2, 9) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
Linear solenoid valve body
mounting bolt 6 6 – For tightening sequence (page 12-
101)
Shift spindle angle sensor bolt 1 6 12 (1.2, 9)
Primary drive gear mounting bolt 1 10 93 (9.5, 69) Apply engine oil to the threads and
seating surface.
Reduction gear cover bolt 3 6 14 (1.4, 10)
TR sensor bolt 1 6 12 (1.2, 9)
Shift control motor bolt 3 6 14 (1.4, 10)
Shift drum center bolt 1 8 23 (2.3, 17) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
Drum shifter guide plate bolt 2 6 12 (1.2, 9) Apply locking agent to the threads.
Coating width: 6.5 ± 1.0 mm (0.26 ±
0.04 in) except 2.0 ± 1.0 mm (0.08 ±
0.04 in) from tip
Clutch line EOP sensor 3 10 19.6 (2.0, 14)
EOT sensor 1 10 14 (1.4, 10) Apply engine oil to the threads and
seating surface.