Honda Miimo HRM310 Owner'S Manual Download | Manualshive

Page: 9 / 88

background image

7

2 SAFETY

INSTRUCTIONS

Precautions / Observe the following points for your safety

• Do not use automatic lawn watering systems while the lawn

mower is operating, because the watering equipment may become
damaged and the likelihood of water penetrating into the lawn
mower is greatly increased. Adjust the work timer of the lawn mower
so the watering systems and the lawn mower do not operate at the
same time.

• If there is a risk of adverse weather such as lightning or a storm, stop operation and disconnect the power cord.

• Parts of this product may become warm in direct sunlight. Make sure you do not touch these parts if they

become extremely hot or you may burn yourself.

• Do not charge the lawn mower with anything other than the docking station. Injury may occur or the lawn

mower may be damaged.

• If the power supply cord is damaged, immediately unplug it from the outlet and contact your dealer. Do not

touch the damaged part of the power supply cord.

• If there are any holes in the work area,

fi

ll them in so that the work area is level. Periodically check the work

area for holes.

Observe the following points for your safety

• When carrying the lawn mower, turn it off and carry it as explained in this manual (see page 59) with the

blades facing away from you.

• When carrying the lawn mower, make sure to carry it by the

designated areas (see page 59). If you carry the lawn mower in any
other way, you risk injury from the blades or charging socket of the
lawn mower.

• Always use thick work gloves when performing maintenance. If you

do not, you may be injured by the blades.

• Before operation, always check the work area and remove any

branches, rocks, and other objects that can damage the blades and
cause the lawn mower to stop. If you do not, you may be injured from
objects that are ejected from the bottom of the lawn mower.

«
...
7
8
9
10
11
...
»

Summary of Contents for Miimo HRM310

























































































Reviews:

No comments

Related manuals for Miimo HRM310

Brand: Walker Pages: 72

Brand: Toro Pages: 2

Brand: Yazoo Pages: 8

Brand: SaMASZ Pages: 41

Brand: Baroness Pages: 93

Brand: Husqvarna Pages: 20

Brand: Husqvarna Pages: 3

Brand: Husqvarna Pages: 9

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 15

Brand: Husqvarna Pages: 88

Brand: Husqvarna Pages: 48

Brand: Husqvarna Pages: 8

Brand: Husqvarna Pages: 21

Brand: Husqvarna Pages: 16

Brand: Husqvarna Pages: 15

Brand: Husqvarna Pages: 20

Brand: Husqvarna Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands