background image

3

SETTING UP YOUR NEW 
MOWER

Unpacking

Remove all the cardboard from around the handlebar.

Handlebar Setup

Raise the handlebar into the mowing position with the handlebar 
adjust knobs in the unlock position.

Turn the adjust knobs 90 degrees into the lock position so the pins will 
spring into the holes and lock into position.

Grass Bag Assembly

Slide the grass bag frame into the grass bag and attach the clips as 
shown.

Lift the discharge guard, remove the mulching plug, and install the 
grass bag.

Engine Oil

The mower is shipped 

WITHOUT OIL

 in the engine.

A bottle of oil is included in 
the box with your mower. 
Add the entire contents of 
the oil bottle into the oil filler 
opening.

All Honda engines are run at 
the factory prior to 
packaging. Most of the oil is 
removed prior to shipment; 
however, some oil remains in 
the engine. The amount of oil 
left in the engine varies.

If not using the supplied oil, 
add enough SAE 10W-30 
API service category SJ or 
later oil to bring the oil level 
between the upper and lower 
limit marks on the dipstick as 
shown.

Do not overfill the engine 
with oil. If the engine is 
overfilled, the excess oil may 
get transferred to the air 
cleaner housing and air cleaner.

After filling the engine with oil, remove the hang tag near the recoil 
starter grip that says “

The engine has no oil. A container of oil is in the 

shipping box

.”

Fuel

Refer to page 12.

Before Operation

Before using the lawn mower, all mower operators must read the 
following sections:

LAWN MOWER SAFETY

 (page 2)

CONTROL LOCATIONS 

(page 4)

BEFORE OPERATION

 (page 4)

OPERATION

 (page 6)

MAINTENANCE SCHEDULE

 (page 8)

You can also find additional information on the Honda Power 
Equipment web site. Visit www.hondapowerequipment.com/faq.htm

Please Register Your Lawn Mower

If your dealer did not collect registration information from you, please 
take a few minutes and register your purchase with Honda. This 
allows us to contact you with any important updates regarding your 
mower. Please note registration is not required to obtain warranty 
service.

You can register by completing and mailing the included registration 
card, or go online to www.hondapowerequipment.com and click on 
Product Registration Owner Link ™.

HANDLEBAR 
ADJUST KNOB (2)

UNLOCK

LOCK

GRASS BAG

BAG
FRAME

PLASTIC CLIP

BAG FRAME

UPPER LIMIT

LOWER LIMIT

FILLER 
CAP/DIPSTICK
(do not screw in the 
dipstick when 
checking the oil level)

Summary of Contents for HRR216VXA

























Reviews: