Honda Forza 750 2020 Manual Download

Page: 152 / 211

Drive Chain

Inspecting the Drive Chain

Slack

Check the drive chain slack at several points

along the chain. If the slack is not constant at

all points, some links may be kinked and

binding.

Have the chain inspected by your dealer.

Shift the transmission to Neutral. Stop the

engine.

Place your vehicle on its centre stand on a

firm, level surface.

Check the slack in the lower half of the

drive chain midway between the

sprockets.

While depressing the drive chain,

measure the distance from the bottom

of the swingarm to the drive chain.

Drive chain slack:

Swingarm to drive chain

40 - 45 mm (1.6 - 1.8 in)

Do not ride your vehicle if the slack

exceeds 50 mm (2.0 in).

20201009081441_32MKV6000_eng_BOOK Page 152 Friday, October 09 2020 08:19:30 JST

Maintenance

149

Continued

Summary of Contents for Forza 750 2020




















































































































































































































Search results

Summary of Contents for Forza 750 2020

Reviews:

Related manuals for Forza 750 2020

Brands by name

Popular brands

Honda Forza 750 2020, Manual

Search results

Summary of Contents for Forza 750 2020

Reviews:

Related manuals for Forza 750 2020

Brands by name

Popular brands