manualshive.com logo in svg

Honda Forza 300 2013, Owner'S Manual, Page: 71 / 119

Share
Download
Honda Forza 300 2013 Owner'S Manual Download Page 71

Engine Oil

 

u

 Adding Engine Oil

68

Mainten

a

nce

Adding Engine Oil

If the engine oil is below or near the lower 
level mark, add the recommended engine oil. 

2

P. 109

1.

Add the recommended oil until it reaches 
the upper level mark.

u

Place your scooter on its centre stand 
on a firm, level surface when checking 
the oil level.

u

Do not overfill above the upper level 
mark.

u

Make sure no foreign objects enter the 
oil filler opening.

u

Wipe up any spills immediately.

2.

Securely reinstall the oil fill cap/dipstick.

For the recommended oil and oil selection 
guidelines, see “Maintenance 
Fundamentals.” 

2

P. 53

Changing Engine Oil & Filter

Changing the oil requires special tools. We 
recommend that you have your scooter 
serviced by your dealer.

1.

Park your scooter on its centre stand on a 
firm, level surface.

2.

If the engine is cold, idle the engine for 3 
to 5 minutes.

NOTICE

Overfilling with oil or operating with insufficient oil can 
cause damage to your engine. Do not mix different brands 
and grades of oil. They may affect lubrication.

NOTICE

Using the wrong oil filter can result in serious damage to 
the engine.

Summary of Contents for Forza 300 2013
























































































































Reviews:

No comments