manualshive.com logo in svg

Honda F220, Owner'S Manual

Share
Download
Honda F220 Owner'S Manual Download Page 37

35

SERVICING YOUR TILLER

HONDA F220 (E) 00X31-V14-6120 -

SPARK PLUG SERVICE

Incorrect spark plugs can cause engine damage.

1. Disconnect the spark plug cap, and remove any dirt from around the

spark plug area.

2. Remove the spark plug with a 5/8-inch spark plug wrench.

3. Inspect the spark plug. Replace it if

the electrodes are worn or the
insulator is cracked, chipped, or
fouled.

4. Measure the spark plug electrode gap

with a wire-type feeler gauge.The gap
should be 0.024 – 0.028 in (0.6 – 0.7
mm). Correct the gap, if necessary, by
carefully bending the side electrode.

5. Install the spark plug carefully, by

hand, to avoid cross-threading.

6. After the spark plug seats, tighten with

a 5/8-inch spark plug wrench to
compress the washer.

If reinstalling a used spark plug, tighten

Recommended spark plugs: CR4HSB (NGK)

U14FSR-UB (DENSO)

SPARK PLUG 
WRENCH

0.024 – 0.028 in
(0.6 – 0.7 mm)

SEALING WASHER

F220_EN.book  35 ページ  ２０１０年２月１２日　金曜日　午前１１時２分

Summary of Contents for F220





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands