Honda EU3200i Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 100

background image

OPERATION

47

When operating generators in parallel operation, if one generator emits exhaust
toward the other, the CO-MINDER® (CO Shut-off System) of the generator that is
receiving the exhaust may stop the engine. Pay attention to the following for
placing generators in parallel operation.
• Align the two generators so that their mufflers are on the same line and exhaust in

the same direction.

• Place the generator so that the muffler is pointed in the same direction as the

wind is blowing and the exhaust is directed away from buildings, other structures,
or vehicles.

EXHAUST

EXHAUST

ON THE SAME LINE

WIND DIRECTION

WIND DIRECTION

This generator may detect exhaust from the
adjacent generator and will stop the engine.

OK

INCORRECT

MUFFLER

«
...
47
48
49
50
51
...
»

Summary of Contents for EU3200i





































































































Reviews:

No comments

Related manuals for EU3200i

Brand: Generac Power Systems Pages: 20

Brand: Leroy-Somer Pages: 31

Brand: Grundig Pages: 162

FG085 Function Generator

Brand: JYE Tech Pages: 2

Brand: A2Z Ozone Pages: 14

Brand: Audiovox Pages: 32

Brand: Audiovox Pages: 29

Brand: Audiovox Pages: 28

Brand: Audiovox Pages: 31

Brand: Audiovox Pages: 33

Brand: Audiovox Pages: 33

Brand: Audiovox Pages: 31

Brand: Audiovox Pages: 32

Brand: Audiovox Pages: 33

D1817 - DVD Player - 8

Brand: Audiovox Pages: 39

Brand: Audiovox Pages: 68

Brand: Aim-TTI Pages: 100

RGX305, RGX305D, RGX405, RGX40

Brand: Robin America Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands