Honda EU3200i Owner'S Manual Download

Page: 11 / 100

GENERATOR SAFETY

Fire and Burn Hazards

• The exhaust system gets hot enough to ignite some materials.

– Keep the generator at least 3 feet (1 meter) away from buildings and any

type of vehicle, trailer, boat, or other equipment during operation.

– Do not enclose the generator in any structure.
– Keep flammable materials away from the generator.
– Do not block intake or exhaust vents, hoses, ports, or restrict air into or

away from generator.

– Do not add, remove, or modify covers, panels, cowlings, or straps.

• The muffler becomes very hot during operation and remains hot for a while

after stopping the engine. Be careful not to touch the muffler while it is hot.
Let the engine cool before storing the generator.

• Do not pour the water directly on the generator to put out the fire when it

occurs. Use an appropriate fire extinguisher specially designed for electric fire
or oil fire.

Refuel With Care

Gasoline is highly flammable, and gasoline vapor can explode.

• Do not refuel during operation.

• Allow the engine to cool if it has been in operation.

• Refuel only outdoors in a well-ventilated area and on a level surface.

• Never smoke near gasoline, and keep other flames and sparks away.

• Do not overfill the fuel tank.

• Make sure that any spilled fuel has been wiped up and cleaned before

starting the engine.

• Always store gasoline in an approved container.

Summary of Contents for EU3200i





































































































Search results

Summary of Contents for EU3200i

Reviews:

Related manuals for EU3200i

Brands by name

Popular brands

Honda EU3200i, Owner'S Manual

Search results

Summary of Contents for EU3200i

Reviews:

Related manuals for EU3200i

Brands by name

Popular brands