Honda EU2200i Owner'S Manual Download Page 38

Page: 38 / 104

BEFORE OPERATION

The Oil Alert system will automatically stop the engine before the oil level falls
below safe limits. However, to avoid the inconvenience of an unexpected
shutdown, check the oil level regularly.

AIR FILTER CHECK

1. Loosen the maintenance cover

screw and remove the
maintenance cover.

2. Loosen the air cleaner cover screw,

and remove the air cleaner cover.

3. Remove the main and outer filters

from the air cleaner housing.

4. Check the main and outer filters to be sure they are clean and in good

condition. If the main and outer filters are dirty, clean them as described on
page 60. Replace the main and outer filters if they are damaged.

MAIN FILTER

MAINTENANCE COVER
SCREW

MAINTENANCE COVER

AIR CLEANER
COVER SCREW

OUTER FILTER

AIR CLEANER COVER

31Z446100.book 36 ページ２０２０年２月１７日　月曜日　午前１１時４１分

Summary of Contents for EU2200i









































































































Search results

Summary of Contents for EU2200i

Reviews:

Related manuals for EU2200i

Brands by name

Popular brands

Honda EU2200i, Owner'S Manual

Search results

Summary of Contents for EU2200i

Reviews:

Related manuals for EU2200i

Brands by name

Popular brands