Honda CRF300L Manual Download Page 71

Page: 71 / 125

Recommended Coolant

Pro Honda HP Coolant is a pre-mixed solution

of antifreeze and distilled water.

Concentration:

50% antifreeze and 50% distilled water

A concentration of antifreeze below 40% will

not provide proper corrosion and cold

temperature protection.

A concentration of up to 60% will provide better

protection in colder climates.

FO type, Hong Kong, Macau

Use only genuine HONDA PRE-MIX COOLANT

without diluting with water. Genuine HONDA

PRE-MIX COOLANT is excellent at preventing

corrosion and overheating.

The coolant should be inspected and replaced

properly by following the maintenance

schedule.

P. 58

NOTICE

Using coolant not specified for aluminium

engines or tap/mineral water can cause corrosion.

Crankcase Breather

Service more frequently when riding in rain, at

full throttle, or after the vehicle is washed or

overturned. Service if the deposit level can be

seen in the transparent section of the drain

tube.

If the drain tube overflows, the air filter may

become contaminated with engine oil causing

poor engine performance.

20200914163746_32K1TB000_eng_BOOK Page 71 Monday, September 14 2020 16:42:25 JST

Maintenance Fundamentals

Maintenance

Summary of Contents for CRF300L






























































































































Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands

Honda CRF300L, Manual

Search results

Summary of Contents for CRF300L

Reviews:

Related manuals for CRF300L

Brands by name

Popular brands