background image

 

CUSTOMER INFORMATION: 

The information in this bulletin is intended for use only by skilled technicians who have the proper tools, 

equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and 
you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this 
information applies, contact an authorized Honda automobile dealer. 

 

© 2017 American Honda Motor Co., Inc. – All Rights Reserved  

Page 

1

 of 

9

 

 

 

Service Bulletin 

17-070

 

August 8, 2017 

07127 Version 1

 

2018 Civic Type R: PDI Information 

AFFECTED VEHICLES 

Year 

Model 

Trim Level 

2018 

Civic  

Type R Touring 

INTRODUCTION 

This bulletin covers the pre-delivery inspection (PDI) of the 2018 Civic Type R. It includes these procedures: 

1. 

Fuel the Vehicle 

8. 

Remove the Front Suspension Height Retainers 

2. 

Remove the Exterior Protective Coatings 

9. 

Install the Front License Plate Holder 

3. 

Install the Fuses 

10. 

Set the Tire Pressures 

4. 

Remove the Interior Protective Coverings 

11. 

Start the TPMS Calibration Process 

5. 

Install the Floor Mats 

12. 

Do the PCM Idle Learn Procedure   

6. 

Check the Battery  

13. 

Install the Shift Lock Release Cover 

7. 

Install the Body Plugs 

14. 

Check/Refresh the SiriusXM

®

 Radio Dealer Demo 

Service  

To do a PDI on the navigation system, be sure to complete S/B 17-071, 

2018 Civic Type R: PDI of the Navigation 

System

CLAIM INFORMATION 

Reimbursement Time: 1.4 hours 

NOTE: This time includes the PDI of the navigation system. 

 

 

Summary of Contents for Civic Type R 2018










Reviews: