Honda CBR650F 2014 Owner'S Manual Download Page 62

Page: 62 / 133

Removing & Installing Body Components

Battery

Mainten

nce

Battery

❙

Removal

Make sure the ignition switch is off.

Remove the seat.

P. 59

Unhook the rubber strap from front side.

Disconnect the negative

terminal from

the battery.

Disconnect the positive

terminal from

the battery.

Remove the battery taking care not to
drop the terminal nuts.

❙

Installation

Install the parts in the reverse order of
removal. Always connect the positive

terminal first. Make sure that bolts and nuts
are tight.
Readjust the clock after the battery is
reconnected since the clock goes wrong
once the battery disconnected.
For proper handling of the battery, see
“Maintenance Fundamentals.”

P. 48

“Battery Goes Dead.”

P. 96

Rubber
strap

Battery

Positive
terminal

Negative
terminal

Summary of Contents for CBR650F 2014






































































































































Search results

Summary of Contents for CBR650F 2014

Reviews:

Related manuals for CBR650F 2014

Brands by name

Popular brands

Honda CBR650F 2014, Owner'S Manual

Search results

Summary of Contents for CBR650F 2014

Reviews:

Related manuals for CBR650F 2014

Brands by name

Popular brands