Honda CBR1000RR Fireblade 2021 Manual Download Page 69

Page: 69 / 239

QUICK SHIFTER

CBR1000SP

You can change the setting of the Quick

Shifter.

UP: Change the setting for upshifting.

DOWN: Change the setting for downshifting.

OFF

Deactivate

SOFT

Activate

MEDIUM
HARD

SOFT, MEDIUM or HARD indicate the load

level of the shift pedal.

To use the Quick Shifter:

(

P.114

)

Select the "UP" or "DOWN" using the

sel

up or

sel down switch.

Select to the desired setting according to

the switch operation guide.

Return to the ordinary display or upper

hierarchy to complete the setting.

20200219171806_31MKR6000_enu_BOOK Page 70 Wednesday, February 19 2020 17:28:26 JST

Operation Guide

Continued

Summary of Contents for CBR1000RR Fireblade 2021
















































































































































































































































Search results

Summary of Contents for CBR1000RR Fireblade 2021

Reviews:

Related manuals for CBR1000RR Fireblade 2021

Brands by name

Popular brands

Honda CBR1000RR Fireblade 2021, Manual

Search results

Summary of Contents for CBR1000RR Fireblade 2021

Reviews:

Related manuals for CBR1000RR Fireblade 2021

Brands by name

Popular brands