manualshive.com logo in svg

Honda BF250A, Owner'S Manual, Page: 35 / 139

Share
Download
Honda BF250A Owner'S Manual Download Page 35

33

CONTROLS AND FEATURES

Oil Pressure Indicator

When the oil pressure indicator is lit, 

oil pressure is OK.

If oil pressure becomes low, the 

indicator will go off, and the engine 

protection system will limit engine 

speed. Refer to 

TAKING CARE OF

 

UNEXPECTED PROBLEMS,

 on 

p. 101.

All models are equipped with a 

buzzer that sounds continuously 

when the oil pressure indicator goes 

off.

Low oil pressure indicates that the 

engine oil level is low or that there is 

a problem with the engine lubrication 

system.

Overheat Indicator

(side-mount type)

OIL PRESSURE

INDICATOR

(GREEN)

BUZZER

(panel-mount/top-mount types)

OIL PRESSURE

INDICATOR

(GREEN)

BUZZER

(side-mount type)

OVERHEAT

INDICATOR

(RED)

BUZZER
(panel-mount/top-mount types)

OVERHEAT

INDICATOR

(RED)

BUZZER

31ZX26040.book  Page 33  Friday, July 25, 2014  5:14 PM

Summary of Contents for BF250A












































































































































Reviews:

No comments