manualshive.com logo in svg

Honda BF250A, Owner'S Manual, Page: 19 / 139

Share
Download
Honda BF250A Owner'S Manual Download Page 19

17

CONTROLS AND FEATURES

Emergency Stop Switch Clip and 

Emergency Stop Switch

The emergency stop switch clip must 

be inserted in the emergency stop 

switch in order for the engine to start 

and run. The emergency stop switch 

lanyard must be attached securely to 

the operator or to the operator’s PFD 

(Personal Flotation Device).

When used as described, the 

emergency stop switch clip and 

emergency stop switch lanyard 

system stops the engine if the 

operator falls away from the controls.

A spare switch clip is stored in a slot 

in the control housing (optional 

equipment).

Gearshift/Throttle Control 

Lever

The gearshift/throttle control lever 

controls engine speed and selects F 

(forward), N (neutral), or R (reverse) 

gears.

EMERGENCY

STOP SWITCH

EMERGENCY STOP

SWITCH CLIP

EMERGENCY

STOP SWITCH

CLIP

EMERGENCY

STOP SWITCH

LANYARD

EMERGENCY

STOP SWITCH

LANYARD

SPARE SWITCH CLIP

GEARSHIFT/THROTTLE

CONTROL LEVER

NEUTRAL RELEASE

LEVER

31ZX26040.book  Page 17  Friday, July 25, 2014  5:14 PM

Summary of Contents for BF250A












































































































































Reviews:

No comments