manualshive.com logo in svg

Honda BF250A, Owner'S Manual, Page: 100 / 139

Share
Download
Honda BF250A Owner'S Manual Download Page 100

98

TAKING CARE OF UNEXPECTED PROBLEMS

FUSES

Electric Starter Will Not 

Operate

The 10 A, 15 A, and 30 A main fuses 

protect the electric starter relay and 

related circuits.

The 30 A main fuse protects the 

ignition switch and related circuits. If 

this fuse blows, the engine will not 

start or run.

Battery Will Not Charge

A 150 A ACG fuse protects the 

alternator circuit. If the ACG fuse 

blows, the engine will not charge the 

battery. Refer to 

ACG Fuse 

(p. 100).

Fuse Replacement

Disconnect the battery cable at the 

battery negative (–) terminal before 

replacing the f use.

Failure to do so may cause a short 

circuit.

Main Fuse

1. Stop the engine.

2. Disconnect the battery.

3. Remove the engine cover (p. 63).

4. Open the junction box cover.

JUNCTION 

BOX 

COVER

SPARE FUSES 

(10 A, 15 A, 30 A)

MAIN FUSES 

(10 A, 15 A, 30 A)

FUSE PULLER

31ZX26040.book  Page 98  Friday, July 25, 2014  5:14 PM

Summary of Contents for BF250A












































































































































Reviews:

No comments