Honda BF200D Manual Download Page 30

Page: 30 / 152

CONTROLS AND FEATURES

Fast Idle Lever (R1 type)/Fast Idle

Button (R2, R3 types)

The fast idle lever/fast idle button is

only needed for starting carbureted

outboard models. The BF200D,

BF225D and BF250D models use

programmed fuel injection so, this

lever will not be needed for starting.

After the engine starts and if the

outside temperature is below

5°C (41°F), the fast idle lever/fast

idle button can be used to accelerate

engine warm up.

<Fast Idle Lever>

(R1 type)

The fast idle lever will not move

unless the remote control lever is in

the NEUTRAL position. Conversely,

the remote control lever will not

move unless the fast idle lever is in

the lowest position.

Lower the fast idle lever to the lowest

position to decrease the fast idle.

<Fast Idle Button>

(R2 type)

Pushing the fast idle button, turn the

remote control lever forward. Keep

turning the lever forward. The throttle

opens and the engine speed increases

after the lever passed the shift point.

Note that the gearshift mechanism

does not function when the fast idle

button is pushed once and then

released after the remote control lever

is moved.

The control lever does not operate

unless the neutral release lever is

pulled.

NEUTRAL

FAST IDLE LEVER

LOWEST

POSITION

MAXIMUM

FAST IDLE

NEUTRAL

FAST IDLE

BUTTON

REVERSE

REMOTE

CONTROL

LEVER

FORWARD

NEUTRAL

RELEASE

LEVER

Push

Pull up

42ZVL600.book 30 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands