Honda BF200D Manual Download Page 128

Page: 128 / 152

128

MAINTENANCE

8. Align the aligning mark as shown

in the figure, when installing the

suspension strap on the fuel filter

with water separator.

9. Prime the engine using the priming

bulb (see page 67). Check for fuel

leaks. Repair any fuel leaks if

necessary.

If the buzzer sounds, water or

sediment accumulation is found to be

caused by excessive water or

sediment accumulated in the fuel

filter, inspect the fuel tank. Clean the

fuel tank if necessary.

EMISSION CONTROL SYSTEM

The combustion process produces

carbon monoxide and hydrocarbons.

Control of hydrocarbons is very

important because under certain

conditions, they react to form

photochemical smog when subjected

to sunlight. Carbon monoxide dose

not react in the same way, but it is

toxic.

Problems that May Affect Outboard

Motor Emissions

If you are aware of any of the

following symptoms, have the

outboard motor inspected and

repaired by your authorized Honda

Dealer:

1. Hard starting or stalling after

starting

2. Rough idle

3. Misfiring or backfiring during

acceleration

4. Poor performance (driveability)

and poor fuel economy

ALIGNING MARK

SUSPENSION STRAP

42ZVL600.book 128 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands