Honda BF200D Manual Download Page 125

Page: 125 / 152

125

MAINTENANCE

Fuel Filter with Water Separator

The fuel filter with water separator is

located near the junction box.

Water or sediment accumulated in the

fuel filter with water separator can

cause loss of power or hard starting.

Check and replace the fuel filter with

water separator periodically.

Clean it or consult with an authorized

Honda outboard motor dealer for

cleaning.

Inspection interval:

Every 100 operating hours or 6

months.

Replacement interval:

Every 400 operating hours or 2 years

FUEL FILTER with

WATER SEPARATOR

WARNING

Gasoline is extremely flammable,

and gasoline vapor can explode,

causing serious injury or death.

Do not smoke or allow flames or

sparks in your working area.

• Always work in a well-

ventilated area.

• Be sure that any fuel drained

from the outboard motor is

stored in a safe container.

• Be careful not to spill fuel

when replacing the filter.

Spilled fuel or fuel vapor may

ignite. If any fuel is spilled,

make sure the area is dry

before starting the engine.

• KEEP OUT OF REACH OF

CHILDREN.

42ZVL600.book 125 ページ２０１８年７月１９日　木曜日　午前９時６分

Summary of Contents for BF200D

























































































































































Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands

Honda BF200D, Manual

Search results

Summary of Contents for BF200D

Reviews:

Related manuals for BF200D

Brands by name

Popular brands