HONDA marine BF25D Owner'S Manual Download Page 35

Page: 35 / 141

CONTROLS AND FEATURES

Overrev Limiter

The engine is equipped with an

overrev limiter to prevent the

possibility of mechanical damage

from excessive engine speed.

The overrev limiter may be activated

during operation, limiting engine

speed, if the outboard motor is tilted

excessively, or when propeller

ventilation occurs during a sharp turn.

If the overrev limiter is activated,

check the trim angle of the outboard

motor.

Check to see if the correct propeller is

installed.

Portable Fuel Tank

[standard equipment (Canadian

types)]

[optional equipment (American

types)]

The portable fuel tank has a capacity

of 6.6 US gal (25L) and has a fuel

gauge built into the fuel tank

connector.

Fuel Filler Cap Vent Knob

The fuel filler cap is provided with a

vent knob to seal the portable fuel

tank for carrying it to and from the

boat. Turn the portable fuel tank vent

knob counterclockwise to the open

position before starting the engine.

OPEN

CLOSE

VENT KNOB

FUEL FILLER CAP

31ZW26430.book Page 33 Monday, November 19, 2018 4:42 PM

Summary of Contents for BF25D












































































































































Search results

Summary of Contents for BF25D

Reviews:

Brands by name

Popular brands

HONDA marine BF25D, Owner'S Manual

Search results

Summary of Contents for BF25D

Reviews:

Brands by name

Popular brands