background image

Hardware List

Part List

Kitchen Island

IMPORTANT

Cam Lock

15 pcs. (+2 extra)

Cam Lock Screw

15 pcs. (+1 extra)

1/2”
Round Head Screw

4 pcs. (+1 extra)

3/4”
Round Head Screw

8 pcs. (+1 extra)

1”
Round Head Screw

16 pcs. (+1 extra)

M6x35
Head Cap Bolt

20 pcs. (+1 extra)

Magnet

2 pcs.

M4x25
Machine Screw

4 pcs.

Flat Washer

8 pcs. (+1 extra)

Adjustable Pin

16 pcs. (+1 extra)

Patent 8,584,600 B2

Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.

Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

B.
Side Panel

1 pc.

C.
Side Panel

1 pc.

D.
Middle Panel

1 pc.

L.
Back Upright

1 pc.

Tool(s) required for assembly:

Level

Phillips screwdriver,

Refer to later page(s) of these
instructions for drawer assembly.

Small Hex Wrench

1 pc.

3/4”
Flat Head Screw

12 pcs. (+1 extra)

H.
Back Rail

1 pc.

G.
Back Rail

1 pc.

F.
Front Rail

1 pc.

E.
Front Rail

1 pc.

I.
Shelf

4 pcs.

M.
Door

1 pc.

N.
Door

1 pc.

K.
Back Panel

2 pcs.

J.
Base

1 pc.

O.
Drawer

2 pcs.

Hex Wrench

1 pc.

Knob

4 pcs.

5008-941

Cartons 50

942 and 5008 943 or 5009 943 are also needed for assembly.

08-

-

-

styles Customer Service: www.homestylesfurniture.com,

home

[email protected],

888-680-7460

Summary of Contents for 5008-941













Reviews: