HomeSeer HS-FS100+ Manual Download Page 1

 

HomeSeer | 10 Commerce Park North, Unit 10 | Bedford, NH 03110 | HomeSeer.com | Doc: HS-FS100-en-v9  

HS-FS100+ Z-Wave Flex Sensor 

 

Use to trigger events based on changes in temperature 

Use the built-

 

 

Example: 

“Dehumid

ifi

er is full” indicator turns on 

 

 

 

Flex Sensor is equipped with a Z-

th an AC 

-Wave commands 

-in buzzer.  

 

 

le-

 

Reset 

-Wave controller is missing or otherwise inoperable). 

 

Press and hold the

 Z-Wave bu�on on the sensor body for 10 seconds. If successful, the LED will flash 5 �mes rapidly.

 

Built

Inclusion / Exclusion

-in Temperature Sensor

 

 

 

Buzzer

 

OVERVIEW

 

HS-FS100+ (“Flex Sensor”) 

external light or water sensors. 

I

t is designed to work with a variet

y

 of Z-

n events or 

scenes.

 

1

A�ach either the light or water sensor cable (if available) to HS-FS100+ before it is powered on, then start the inclusion process.

 

Put your Z-Wave controller into inclusion mode. Consult your controller manual if you’re unsure how to do this.

2

 

HomeSeer users: press “Add Device” on 

y

our Z-Tool+ mobile app

 

Press the Z-Wave network bu�on on the front of the unit one �me, wait for the inclusion process to finish.

INSTALLATION

Add or remove the device into your network by a Z-Wave cer

ti

fied controller. HS-FS100+ supports the latest S2 security offered by

Z-Wave cer

ti

fied controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instruc

ti

ons

on adding or removing devices to/from the network. If not, it will add as a non-secure device, this will not affect the func

ti

onality of

the unit, the device can be added or removed using the following procedure:

The water sensor is designed to detect moisture along the en

ti

re length of its cable. This is especially useful for detec

ti

ng leaks over 

extended distances and around appliances. Op

tio

nal extension cables may be added for coverage of up to 150 feet. The sensor will 

no

ti

fy your controller with a (Water Alarm No�fica�on), event type (Water Leak Detected) command and will beep 5 

ti

mes when water 

is detected. In addi�on, once water is detected, frequency of the beep and no�fica�on to the controller can be configured based on 

parameter 2, the default se�ng is every 10 minutes. Another Z-Wave command will be sent to the controller when water is no longer 

detected. The cable can be reused once it dries. The sensor will check for water every 60 seconds (on ba

tt

ery power) or every 400 ms 

(on line power).

Note:

 Whenever an event such as water leak or light status change is triggered for an extended period of �me, ba�ery life will be 

significantly reduced. A�er such an event, it is recommended to install fresh ba�eries or use USB power supply.

The light sensor can be mounted over any indicator light and will no

ti

fy your controller with an event type (Light Detected No�fica�on), 

if it detects color it will send a different event type (Light Color Change Detected) command and will beep 5 

ti

mes. A “No Event” 

command will be sent to the controller when light is no longer detected. The sensor will check for light every 60 seconds (on ba

tt

ery 

power) or every 400ms (on line power).

The temperature sensor is designed to transmit temperature data to your controller using the command class sensor mul�level, every 60 

minutes (on ba�ery power). That interval may be changed when the unit is on line power, see parameter se�ngs on page 2 for details.

The built in buzzer emits 5 beeps when the device detects water or light. On line power (USB) the associated controller may enable the 

buzzer by sending a command class basic or binary switch set command with a non zero value to the sensor.

Note: When adding or removing op�onal water extension cables, make sure HS-FS100+ is powered off.

Reviews: