1005390722
1
2
3
4
21SV23107 BUBBLE FOGGER MACHINE
USER MANUAL
FOR INDOOR USE ONLY
DON'T USE IT AS A TOY
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT TIPS:
* Ensure that the bubble liquid and fog liquid are poured into the correct corresponding container according to Step 2 below. Always
make sure there is enough bubble liquid and fog liquid in the tank before using the Bubble Fogger.
* Do not remove the drainage caps (J) & (R) when there is liquid in the container unless you intend to drain the item of its contents.
Drain over a trash bin or empty container.
* Make sure that the end of the (H) Tube touches the bottom of the bubble liquid container and that there is no blockage.
* The Bubble Fogger needs time to warm up before it can produce fog. This may take 2-4 minutes. The Bubble Fogger will be ready
to produce fog when the (D) Status Indicator light turns red. When filled to the max fill line, the Bubble Fogger will run for approxi-
mately 70 minutes before running out of fog liquid. Refill when fog liquid has been depleted.
* When the Bubble Machine has preheated (Status Indicator light turns red), turn on the (L) Function Switch to produce fog bubbles.
* When the Bubble Machine Status Indicator light turns blue, the Bubble Machine needs more fog liquid.
* The machine will keep blowing fog bubbles for about 40 seconds and then stop for about 20 seconds before resuming.
* If you have any broken or missing parts, please contact SVI customer service from 8:30am to 5:30pm PST at 1-855-428-3921,
email [email protected], or call The Home Depot customer service at 1-877-527-0313 before returning to the store.
INSTRUCTION
1. Pull the (B) Skull Lid up and
Support as shown. Secure the
(N) Handle to the (A) Bubble
Fogger Machine using the (F)
Handle Screws.
2. Fill the bubble tank and fog
liquid tank up to their max fill
lines. The fan cover will open
automatically when the bubble
fogger machine is running
normally. Do not pour liquid
into the air outlet.
3. Plug the (A) Bubble Fogger
Machine into an outlet, toggle
the (Q) Power Switch behind
the machine to the "I" position.
The (D) Status Indicator will
turn red after the machine heats
up for 2-4 minutes. Then toggle
the (L) Function Switch under
the (B) Skull Lid to "I" to
activate the fog bubbles.
4. There will not be any fog
bubbles within the first 20
seconds as the machine
needs time to pump the bubble
liquid from the tank to the
nozzle. After the first 20
seconds, the machine will start
blowing fog bubbles for about
40 seconds and then stop
for about 20 seconds before
resuming.
DESCRIPTION OF THE APPLIANCE
BU
BBL
E
LIQU
ID
K. Skull Lid Support
L. Function Switch
M. Fog Liquid Tank Cap
N. Handle
O. Fuse
Q. Power Switch
P. Power Cable
R. Fog Liquid Drainage Cap
A. Bubble Fogger Machine
B. Skull Lid
C. Rotating Bubble Wand
D. Status Indicator
F. Handle Screw x2
G. Nozzle
H. Tube
I. Fan Cover
J. Bubble Liquid Drainage Cap
FOG
LIQU
ID
1.1
1.2
1.3
AIR OUTLET
DO NOT POUR LIQUID INTO
THE AIR OUTLET.
Do not pour the
Bubble Liquid into
the (G) Nozzle
where bubbles are
formed. Pour into
the available basin
under the (G)
Nozzle.
POWER SWITCH
STATUS INDICATOR
BLUE LIGHT - Lacks fog liquid
.
RED LIGHT - Ready to activate fog bubbles.
Make sure the
end of the (H)
Tube touches
the bottom of
the container
FUNCTION SWITCH
Set (L)Function Switch to "I"
to activate the fog bubbles.
