manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 528 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 528

Rev. 1.00 

528 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

26  Cyclic Redundancy Check (CRC)

CRC with PDMA

A PDMA channel with software trigger may be used to transfer data into the CRC unit. If a huge 

block data needs to be calculated, the recommended PDMA model is to use the PDMA to transfer 

all available words of data and use software writes to transfer the other remaining bytes. To write 

data into the CRC unit, the PDMA should use word access method to transfer data from the source 

location of memory to the CRC data register (CRCDR) in fixed address mode. Then software can 

write any remaining bytes to the CRC data register (CRCDR) and read the CRC calculation result 

value from the CRC checksum register (CRCCSR).

Register Map

The following table shows the CRC registers and reset values.

Table 66.  CRC Register Map

Register

Offset

Description

Reset Value

CRCCR

0x000

CRC Control Register

0x0000_0000

CRCSDR

0x004

CRC Seed Register

0x0000_0000

CRCCSR

0x008

CRC Checksum Register

0x0000_0000

CRCDR

0x00C

CRC Data Register

0x0000_0000

Register Descriptions

CRC Control Register – CRCCR

This register specifies the corresponding CRC function enable control.
Offset:

0x000

Reset value: 0x0000_0000

31

30

29

28

27

26

25

24

Reserved

Type/Reset

23

22

21

20

19

18

17

16

Reserved

Type/Reset

15

14

13

12

11

10

9

8

Reserved

Type/Reset

7

6

5

4

3

2

1

0

SUMCMPL SUMBYRV SUMBIRV DATCMPL DATBYRV DATBIRV

POLY

Type/Reset RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0

Bits

Field

Descriptions

[7]

SUMCMPL

1’s Complement operation on Checksum Output

0: Disable

1: Enable

[6]

SUMBYRV

Byte Reverse operation on Checksum Output

0: Disable

1: Enable

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments