manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 242 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 242

Rev. 1.00 

242 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

14  General-Purpose T

imer (GPTM)

Single Pulse Mode

Once the timer is set to operate in the single pulse mode, it is not necessary to set the timer enable 

bit TME in the CTR register to 1 to enable the counter. The trigger to generate a pulse can be 

sourced from the STI signal rising edge or by setting the TME bit to 1 using software. Setting the 

TME bit to 1 or a trigger from the STI signal rising edge can generate a pulse and then keep the 

TME bit at a high state until the update event occurs or the TME bit is written to 0 by software. 

If the TME bit is cleared to 0 using software, the counter will be stopped and its value held. If the 

TME bit is automatically cleared to 0 by a hardware update event, the counter will be reinitialized.

Trigger by S/W

Trigger by STI

Cleared by 

Update Event 

Flag is set by compare match and 

cleared by S/W

CRR

CHxCCR

TME bit

STI

UEVIF

CHxCCIF

Counter Value

 

Flag is set by update event

and cleard by S/W 

Counter stopped 

and held

Time

Counter 

reinitialized

Cleared by S/W

Delay

Delay

CHxOREF

(PWM1)

Delay

Delay

(PWM2)

CHxIMAE=0

Min. delay

CHxIMAE=1

Min. delay

CHxOREF

(PWM1)

(PWM2)

Delay

Delay

Figure 66.  Single Pulse Mode

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments