manualshive.com logo in svg

Holtek HT32F54231, User Manual, Page: 234 / 576

Share
Download
Holtek HT32F54231 User Manual Download Page 234

Rev. 1.00 

234 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

14  General-Purpose T

imer (GPTM)

0

1

2

3

4

5

6

7

0

1

2

3

4

5

6

7

4

GT_CH0

(TI0)

CNTR

CH0CCR

CH1CCR

Capture CH0

Restart mode

Reset counter value

Capture CH1

7

Restart mode

Reset counter value

Figure 53.  PWM Pulse Width Measurement Example

Input Stage

The input stage consists of a digital filter, a channel polarity selection, edge detection and a channel 

prescaler. The channel 0 input signal (TI0) can be chosen to come from the GT_CH0 signal or the 

Excusive-OR function of the GT_CH0, GT_CH1 and GT_CH2 signals. The channel input signal 

(TIx) is sampled by a digital filter to generate a filtered input signal TIxFP. Then the channel 

polarity and the edge detection block can generate a TIxS0ED or TIxS1ED signal for the input 

capture function. The effective input event number can be set by the channel capture input source 

prescaler setting field, CHxPSC.

Filter

TI0FP

TI0FN

TI0F

GT_CH0

f

sampling

CH0P

Filter

TI1FP

TI1FN

TI1F

CH1P

GT_CH1

TI0S0

TI1S0

TI0S1

TI1S1

TRCED

CH0PRESCALER

CH1PRESCALER

TI0S0ED

CH0PSC

CH1PSC

CH0CCS

CH1CCS

CH0PSC

CH1PSC

CH0CAP Event

CH1CAP Event

Edge 

Detection

Edge 

Detection

Edge 

Detection

Edge 

Detection

TI1S0ED

TI0S1ED

TI1S1ED

f

CLKIN

GT_CH1
GT_CH2

TI0SRC

TI0XOR

Edge

Detection

Edge

Detection

TI0BED

XOR

f

sampling

TI0

TI1

f

CLKIN

Figure 54.  Channel 0 and Channel 1 Input Stages

Summary of Contents for HT32F54231

































































































































































































































































































































































































































































































































































































Reviews:

No comments