Holtek HT32F50231 User Manual Download Page 250

Page: 250 / 486

Rev. 1.00

250 of 486

July 31, 2018

32-Bit Arm

Cortex

-M0+ MCU

HT32F50231/HT32F50241

14 Pulse W

idth Modulator (PWM)

14 Pulse W

idth Modulator (PWM)

Center-Aligned Counting

In the center-aligned counting mode, the counter counts up from 0 to the counter reload value

and then counts down to 0 alternatively. The Timer module generates an overflow event when the

counter counts to the counter reload value in the up-counting mode and generates an underflow

event when the counter counts to 0 in the down-counting mode. The counting direction bit DIR in

the CNTCFR register is read-only and indicates the counting direction when in the center-align

mode. The counting direction is updated by hardware automatically.

Setting the UEVG bit in the EVGR register will initialize the counter value to 0 irrespective of

whether the counter is counting up or down in the center-aligned counting mode.

The UEVIF bit in the INTSR register can be set to 1 when an overflow or underflow event or both

of them occur according to the CMSEL field setting in the CNTCFR register.

CK_PSC

CNT_EN

CK_CNT

CNTR

CRR Shadow

CRR

Counter Underflow

Update Event Flag

Software clearing

Write a new value

Counter Overflow

Software clearing

Figure 66. Center-aligned Counting Example

Summary of Contents for HT32F50231







































































































































































































































































































































































































































































































Search results

Summary of Contents for HT32F50231

Reviews:

Holtek HT32F50231, User Manual, Page: 250 / 486

Search results

Summary of Contents for HT32F50231

Reviews: