manualshive.com logo in svg

Holtek BS86DH12C, Manual, Page: 163 / 192

Share
Download
Holtek BS86DH12C Manual Download Page 163

Rev. 1.00

162

October 26, 2018

Rev. 1.00 

163

October 26, 2018

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

Over Voltage Protection Interrupt

The OVP Interrupt is controlled by detecting the OVP input voltage. An OVP Interrupt request will 
take place when the OVP Interrupt request flag, OVPF, is set, which occurs when the Over Voltage 
Protection circuit detects an over voltage condition. To allow the program to branch to its respective 
interrupt vector address, the global interrupt enable bit, EMI, and OVP Interrupt enable bit, OVPE, 
must first be set. When the interrupt is enabled, the stack is not full and an over voltage is detected, a 
subroutine call to the OVP Interrupt vector, will take place. When the interrupt is serviced, the OVP 
Interrupt flag, OVPF, will be automatically cleared. The EMI bit will also be automatically cleared 
to disable other interrupts.

Over Current Protection Interrupt

The OCP Interrupt is controlled by detecting the OCP input current. An OCP Interrupt request will 
take place when the OCP Interrupt request flag, OCPF, is set, which occurs when the Over Current 
Protection circuit detects an over current condition. To allow the program to branch to its respective 
interrupt vector address, the global interrupt enable bit, EMI, and OCP Interrupt enable bit, OCPE, 
must first be set. When the interrupt is enabled, the stack is not full and an over current is detected, a 
subroutine call to the OCP Interrupt vector, will take place. When the interrupt is serviced, the OCP 
Interrupt flag, OCPF, will be automatically cleared. The EMI bit will also be automatically cleared 
to disable other interrupts.

High Voltage Short Circuit Interrupt

The High Voltage Short Circuit Interrupt is controlled by detecting the high voltage I/O port circuit 
condition. An High Voltage Short Circuit Interrupt request will take place when its interrupt request 
flag, HVSCF, is set, which occurs when a short circuit situation occurs on any one of the high 
voltage I/O pins. To allow the program to branch to its respective interrupt vector address, the global 
interrupt enable bit, EMI, and High Voltage Short Circuit Interrupt enable bit, HVSCE, must first be 
set. When the interrupt is enabled, the stack is not full and an short circuit condition is detected, a 
subroutine call to the High Voltage Short Circuit Interrupt vector, will take place. When the interrupt 
is serviced, the High Voltage Short Circuit Interrupt flag, HVSCF, will be automatically cleared. The 
EMI bit will also be automatically cleared to disable other interrupts.

TM Interrupts

The Compact and Periodic TMs each have two interrupts, one comes from the comparator A match 
situation and the other comes from the comparator P match situation. All of the TM interrupts are 
contained within the Multi-function Interrupts. For each of the Compact and Periodic TMs there are 
two interrupt request flags and two enable control bits. A TM interrupt request will take place when 
any of the TM request flags are set, a situation which occurs when a TM comparator P or A match 
situation happens.
To allow the program to branch to its respective interrupt vector address, the global interrupt enable 
bit, EMI, the respective TM Interrupt enable bit and the relevant Multi-function Interrupt enable bit, 
MFnE, must also be set. When the interrupt is enabled, the stack is not full and a TM comparator 
match situation occurs, a subroutine call to the relevant TM Interrupt vector locations will take 
place. When the TM interrupt is serviced, the EMI bit will be automatically cleared to disable other 
interrupts. However, only the related MFnF flag will be automatically cleared. As the TM interrupt 
request flags will not be automatically cleared, it has to be cleared by the application program.

Interrupt Wake-up Function

Each of the interrupt functions has the capability of waking up the microcontroller when in the 
SLEEP or IDLE Mode. A wake-up is generated when an interrupt request flag changes from low 

Summary of Contents for BS86DH12C

































































































































































































Reviews:

No comments