Holtek BS82B12A-3 Manual Download Page 77

Page: 77 / 168

Rev. 1.20

�an�a�� 2�� 201�

Rev. 1.20

�an�a�� 2�� 201�

BS82B12A-3/BS82C16A-3/BS82D20A-3

Touch Key 8-Bit Flash MCU with LED/LCD Driver

BS82B12A-3/BS82C16A-3/BS82D20A-3

Touch Key 8-Bit Flash MCU with LED/LCD Driver

Timer/counter Mode

nused

These two bits are used to determine how the CTM0 output pin changes state when a

certain condition is reached. The function that these bits select depends upon in which

mode the CTM0 is running.

In the Compare Match Output Mode, the CT0IO1 and CT0IO0 bits determine how the

CTM0 output pin changes state when a compare match occurs from the Comparator A.

The CTM0 output pin can be setup to switch high, switch low or to toggle its present

state when a compare match occurs from the Comparator A. When the bits are both

zero, then no change will take place on the output. The initial value of the CTM0

output pin should be setup using the CT0OC bit in the CTM0C1 register. Note that

the output level requested by the CT0IO1 and CT0IO0 bits must be different from the

initial value setup using the CT0OC bit otherwise no change will occur on the CTM0

output pin when a compare match occurs. After the CTM0 output pin changes state

it can be reset to its initial level by changing the level of the CT0ON bit from low to

high. In the PWM Mode, the CT0IO1 and CT0IO0 bits determine how the CTM0

output pin changes state when a certain compare match condition occurs. The PWM

output function is modified by changing these two bits. It is necessary to only change

the values of the CT0IO1 and CT0IO0 bits only after the CTM0 has been switched off.

Unpredictable PWM outputs will occur if the CT0IO1 and CT0IO0 bits are changed

when The CTM0 is running.

Bit 3

CT0OC

: TP0 Output control bit

Compare Match Output Mode

0: Initial low

1: Initial high

PWM Mode

0: Active low

1: Active high

This is the output control bit for the CTM0 output pin. Its operation depends upon

whether CTM0 is being used in the Compare Match Output Mode or in the PWM

Mode. It has no effect if the CTM0 is in the Timer/Counter Mode. In the Compare

Match Output Mode it determines the logic level of the CTM0 output pin before a

compare match occurs. In the PWM Mode it determines if the PWM signal is active

high or active low.

Bit 2

CT0POL

: TP0 Output polarity Control

0: Non-invert

1: Invert

This bit controls the polarity of the CTM0 output pin. When the bit is set high the

CTM0 output pin will be inverted and not inverted when the bit is zero. It has no effect

if the CTM0 is in the Timer/Counter Mode.

Bit 1

CT0DPX

: CTM0 PWM period/duty Control

0: CCRP - period; CCRA - duty

1: CCRP - duty; CCRA - period

This bit, determines which of the CCRA and CCRP registers are used for period and

duty control of the PWM waveform.

Bit 0

CT0CCLR

: Select CTM Counter clear condition

0: CTM0 Comparatror P match

1: CTM0 Comparatror A match

This bit is used to select the method which clears the counter. Remember that the

Compact CTM0 contains two comparators, Comparator A and Comparator P, either of

which can be selected to clear the internal counter. With the CT0CCLR bit set high,

the counter will be cleared when a compare match occurs from the Comparator A.

When the bit is low, the counter will be cleared when a compare match occurs from

the Comparator P or with a counter overflow. A counter overflow clearing method can

only be implemented if the CCRP bits are all cleared to zero. The CT0CCLR bit is not

used in the PWM Mode.

Summary of Contents for BS82B12A-3









































































































































































Search results

Summary of Contents for BS82B12A-3

Reviews:

Related manuals for BS82B12A-3

Brands by name

Popular brands

Holtek BS82B12A-3, Manual

Search results

Summary of Contents for BS82B12A-3

Reviews:

Related manuals for BS82B12A-3

Brands by name

Popular brands