background image

GENERAL INSTALLATION DATA

  

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and experienced 

in its operation and is not sold for consumer use in and around the home nor for use directly by the 

general public in food service locations.
Before using your new equipment, read and understand all the instructions & labels associated with the 

unit prior to putting it into operation.  Make sure all people associated with its use understand the units 

operation & safety before they use the unit.
All shipping containers should be checked for freight damage both visible and concealed.  This unit has 

been tested and carefully packaged to insure delivery of your unit in perfect condition.  If equipment is 

received in damaged condition, either apparent or concealed, a claim must be made with the delivering 

carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a 

request for inspection of concealed damage must be made with carrier within 15 days.  Be certain to 

retain all contents plus external and internal packaging materials for inspection.  The carrier will make 

an inspection and will supply necessary claim forms.

INSPECTION & ASSEMBLY 
UNCRATING AND INSPECTING

Unpack the unit and components from the shipping container.  Remove all visible packing 

material and those from inside the cooking chamber.  If damage is discovered, file a claim 

immediately with the carrier that handled the shipment.  Do not operate the unit if it was 

damaged during shipping.

ASSEMBLY AND INSTALLATION

 The unit was shipped fully assembled and ready to plug into a standard outlet specified for 

its voltage and amp draw.  If improper electrical supply is determined, contact a qualified 

electrician prior to using the unit.  Removal and replacement of the power cord and plug will 

void the warranty.  For assistance, contact your local authorized service agent for service or 

required maintenance.

 Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).

 Before using the unit for the first time, wipe down the exterior with a damp cloth.

  

CAUTION

Allow enough space around the toaster for adequate ventilation.  Do not operate the unit 

without the crumb tray properly positioned.  Overheating and poor toasting may occur.  

Read all labels on the unit and follow their instructions.

ELECTRICAL CONNECTION

  

WARNING

Before making any electrical connection to this unit, check that the power supply is adequate for the 

voltage, amperage and requirements stated on the rating plate.   

A wiring diagram is included herewith.
Disconnect the unit from the power source before installing or removing any parts.
Be absolutely sure that the ground connection for the receptacle is properly wired.   

Do not connect equipment to power without proper ground connections.   

Improper grounding may result in personal injury or fatality.

 

Summary of Contents for QCS-2-1200B
















Reviews: