1 2
ASSEMBLY INSTUCTIONS FOR TREE STAND
Fig.1
1. Tree stand consists of a
metal stand and a single
eye bolt. (See Fig.1)
Fig. 2
2. Open the stand to a 90 degree
angle until the hole lines up with
the hole on the tube. (See Fig.2)
Fig. 3
3. Insert an eye bolt and
screw into the hole. (See
Fig.3)
Fig. 4
4. Insert the tree into the stand and
adjust accordingly. The tree
should be straight and balanced
correctly. (See Fig.4)
ASSEMBLY INSTRUCTIONS FOR TREE
1. Before you start to assemble the tree, choose an appropriate location near an outlet.
2. Assemble the tree from the bottom to the top. Assemble tree stand according to the assembly
instruction for the tree stand.
3. Insert bottom section (B) into the tree base and tighten the screw (see Fig.1); Insert the top section (A)
into the bottom section (B) (see Fig. 2).
4. Join the male and female connector according to the magnified drawing. (see Fig. 3)
5. Open all the branches (see Fig. 4).
6. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be
sure that all wires are free of branch hinges (see Fig. 5).
7. Shape the branches and tips working from the bottom to the top. Start with tips farthest from the trunk
and fan out one to the right, one to the left and one at the center of the main stem (see Fig. 5). After
shaping the entire tree, follow the previous step, slightly upsweep all branch tips for a uniform look.
Shift branches to fill any gaps. Your Christmas tree is now ready to be decorated.
8. Insert the plug from the tree into a proper outlet. Now your tree should be completed with all lights
illuminated. Please refer to HOW TO USE THE CONTROL BOX of the assembly instructions to adjust
the control box to choose the desired light pattern.
HOW TO USE THE CONTROL BOX:
Rotate the knob to determine the function selected.
Different choices of light patterns for selection:
1. COMBINATION
2. IN WAVES
3. SEQUENTIAL
4. SLO-GLO
5. CHASING/FLASH
6. SLOW FADE
7. TWINKLE/FLASH
8. STEADY ON
TROUBLE SHOOTING (If Lights Do Not Work):
1. If entire tree does not light, make sure cord plug is securely inserted into a working electrical outlet.
2. Check whether all bulbs are tightly fixed inside the lamp holder.
3. If a bulb is blown or broken, replace the faulty bulb according to bulb replacement instructions below.
4. If the fuse in the cord plug is blown, replace the blown fuse according to fuse replacement
instructions below.
5. If you are still experiencing problems with your tree, please contact our customer service
representative at 866-210-5958.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS POWER
SOURCE BEFORE ATTEMPTING EITHER FUSE OR BULB
REPLACEMENT.
USER AND CARE INSTRUCTIONS
FUSE REPLACEMENT
This product comes with an overload protection (fuse). A blown fuse indicates an overload or short
circuit.
If a fuse blows, unplug tree from wall outlet. Replace the fuse as per the fuse replacement
instructions below (follow product marking for proper fuse rating). If the replacement fuse blows, a
short circuit may be present and the product should be reviewed to determine the cause.
Light set fuse replacement (replaceable 5-amp 125V fuses are located in the
plastic bag)
1. Grasp plug and remove from its power source (Illustration.1).
2. Locate blown fuse(s) by sliding access cover on top of plug towards prongs.
3. Remove blown fuse by turning the plug over. Fuses should fall into your hand
(Gentle tapping may be required).
4. Insert new fuse. Close fuse cover by sliding fuse access cover towards the cord.
CAUTION
: To reduce risk of fire – replace fuse in tree stand plug with
only 5-amp 125 volt fuse (Illustration.1).
Do not replace attachment plug.
Discard product if the attachment plug is damaged.
Illustration 1
