HOESCH Whirlsystem Reviva II, Installation And Operation Instructions Manual, Page: 20 / 84

20
GB
12 Automatic switching-off of the system
The operational time of the system is limited to 25 minutes. After
25 minutes, regardless of the buttons switched on, the system
switches-off automatically. By pressing button 1 and/or 4 you can
switch the system on again.
13 Ozonation (only with Airsystem, Whirlpower
and Whir Air)
Ozonization is automatically activated when the blower is turned
on.
14 System drying (only with Airsystem,
Whirlpower and Whir Air)
The system drying function is switched on automatically approx.
10 minutes after emptying the bathtub. After switching on it works
in total for about 2 minutes, during which the blower works for the
fi rst 30 seconds with medium power, and for the next 90 seconds
with full power. While emptying the bathtub you can manually
switch on the system drying of air and whirl jets by pressing
button 4 (duration approx. 2 minutes). The system drying can
be switched-off at any moment.
15 Disinfection
Regular disinfection of your whirltub guarantees optimal
hygiene. When the tub is not used for longer period of time,
it is necessary to make disinfection before running the
tub! If disinfection is necessary, you will be informed about
that with yellow LED diode lighting up when you finish the
bath. In order to run disinfection, there must be certain
level of water- alternatively, the water level must be raised
to the required level at which it is also possible to activate
underwater spotlight.
⚠
We do not hold the responsibility for damages and
threats occurred because of usage of other agents
not intended for this purpose.
■ After leaving the
bathtub pour the
disinfecting agent
into it (follow
the producer's
instructions!).
In automatic
disinfection system
(No. 69712)
the disinfecting agent
(follow the producer's
instructions!) has to
be placed in the
disinfectant container.
See drawing. We recommend using the disinfecting
agent with the article No. 6923 or 133607.
Dosing for Art.-Nr. 133607 can diff er!
Suggested amounts: 100 ml of the disinfecting agent for
100 L of the bathtub capacity.
Producers tips should be observed
■ Start the disinfection by pressing „Des“ button
10 (hold the button pressed for min. 3 seconds).
During the disinfection (duration time approx. 30
minutes) the red LED diode is on.
The process of the disinfection
■ First the system works for 1 minute in order to distribute
the disinfecting agent.
■ After the time of the agent’s interaction, which lasts 27
minutes, the system is switched on again for 2 minutes.
■ After fi nishing the programme, the red LED diode starts
pulsating, which means that the bathtub should be
emptied.
■ After emptying the bathtub and rinsing its surface, pipes
of air and water jets are automatically dried up (only with
Airsystem, Whirlpower and Whir Air)
■ If the disinfection process is interrupted, the yellow LED
diode will be still on!
16 Usage and maintenance
Usage
In general, bathing in the water massage bathtub is a relax or
great fun. However, for a small group of people it may cause a
threat to their health.
In case of doubts consult a doctor.
In case of the following group of people/users we advise against
using the water massage bathtub:
■ Babies up to 1 year old
■ People with unstable blood circulation
■ After consuming a big amount of alcohol
■ People with a cold or fl u
■ In case of problems with the heart/blood circulation
■ After a visit in sauna use the bubble bath after a longer
break during which you cool down
■ Immediately after eating
■ When the jets is used by children, they should be under
constant supervision of adults.
■ When older or disabled people with limited physical
abilities use the jets, special caution should
be exercised.
■ Specialized companies and the fi rst user declare
that they will make the operating manual available
for subsequent owners and users.
The temperature of water in the jets should not exceed the
average body temperature. The ideal scope of temperatures is
from + 32°C to + 37°C.
For your own safety please make sure that no electric devices
or other current conducting elements will not fall into the bathtub
fi lled with water.
Maintenance
Additives for bathing containing solids, such as turf, oils, etc.,
cannot be used. We recommend to use HOESCH foam baths for
whirltubs.
After a bath rinse the bathtub surface with water and wipe it with
a wet cloth.
Do not use scrubbing agents! When occasionally
cleaning the bathtub thoroughly, spread a couple drops of
the cleaning agent on the surface and wipe it with a soft cloth.
Remove heavier dirt using warm water and a mild liquid cleaning
agent, or soap water.
Calcifi cations should be removed with the use of lime removing
vinegar and water
(do not use these for fittings!) . In case of
using the agents for cleaning drains please observe the usage
instructions!
Small scratchings or fragments of the shiny surface that have
lost their smoothness should be removed with the use of e.g. the
HOESCH maintenance set, article No.: 699100.
Tip:
Fittings and built-in elements should be cleaned with a soft cloth.
Damages caused as a result of improper usage of chemicals,
acids and scrubbing agents will not be taken into consideration by
us as the reason of a complaint.
MAX 500ml