background image

Warranty

AquaCraft will warrant this kit for 90 days after
the  purchase  from  defects  in  materials  or
workmanship.  AquaCraft  will  either  repair  or
replace, at no charge, the incorrectly made part.

Make  sure  you  save  the  receipt  or  invoice  you
were  given  when  you  bought  your  model!  It  is
your proof of purchase and we must see it before
we can honor the warranty.

To  return  your  Paradise  Sailboat    for  repairs
covered  under  warranty  you  should  send  your
boat to:

Hobby Services 

3002 N. Apollo Drive Suite 1

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007

9:00 am - 5:00 pm Central Time M-F
E-mail: 

[email protected]

HCAZ3022 for HCAB01**

Entire Contents © Copyright 2004

Before Building:

Thank you for purchasing the Paradise sailboat! We at AquaCraft know how exciting a new R/C boat purchase can be and we
know you’re anxious to get started, but please take time to read the instructions carefully and completely before attempting to
operate your model. This manual contains the instructions you need to safely build, operate, and maintain your R/C sailboat. 

If for any reason you think that this model is not for you, return it to your local dealer immediately. PLEASE NOTE: Your
hobby dealer cannot accept a return on any model after the final assembly sequence has begun.

ASSEMBLY AND OPERATION MANUAL

by

Summary of Contents for Paradise AquaCraft













Reviews: