HNP Mikrosysteme mzr-7240 Operating Manual Download Page 18

Page: 18 / 89

4 Description

Operating manual mzr-7240

Technical data subject to change without prior notice!

Last update: March 2019

The resistance of the construction materials to the delivered liquids should be

verified by the operator for each individual application. Pumps handling non-

lubricating liquids have shorter service lives.

4.4

Fluidic connectors of mzr-7240

Fluidic connectors

Construction mzr-7241

Construction mzr-7245

lateral 1/8" NPT internal
thread

Tubes, square, screw

Tubes, round, bearing bracket -

table 6

Fluidic connectors

The micro annular gear pump head has an inscription on the front side. The

liquid inlet connection is marked with the letter »S«, the liquid outlet

connection with the letter »D«. An arrow indicates the inherent turning

direction of the shaft.

In order to prevent foreign bodies from penetrating into the pump, the liquid

inlet and outlet are protected with plastic plugs or screws. Please remove them

before you assembly the pump.

Summary of Contents for mzr-7240


























































































Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands

HNP Mikrosysteme mzr-7240, Operating Manual

Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands